 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Data Sheet DiskOnChip(R) Millennium Plus 16/32/64MByte Flash Disk with Protection and Security-Enabling Features Highlights DiskOnChip Millennium Plus is an award-winning member of M-Systems' family of DiskOnChip flash disk products. To meet the needs of a growing application base, M-Systems offers it in two form factors, TSOP-I and BGA, in capacities of 16MByte (128Mbit), 32MByte (256Mbit) and 64MByte1 (512Mbit). DiskOnChip Millennium Plus, based on Toshiba's stateof-the-art 0.16 NAND flash technology, features: Advanced protection and security-enabling features for data and code Proprietary TrueFFS(R) technology for full hard-disk emulation, high data reliability and maximum flash lifetime Device cascade options for up to 128MByte (1Gbit) capacity Small form factors: 48-pin TSOP-I and 69-ball BGA NAND-based flash technology that enables high density and small die size Single-die chip: 16MByte and 32MByte, dual-die chip: 64MByte Exceptional read, write and erase performance Configurable for 8/16/32-bit bus interface Programmable eXecute In Place (XIP) Boot Block Data integrity with Reed-Solomon-based Error Detection Code/Error Correction Code (EDC/ECC) Deep Power-Down mode for reduced power consumption Low voltage: Core - 3V, I/O - 1.8V/3V auto-detect (16MByte device) Software tools for programming, duplicating, testing and debugging Support for all major OSs, including: Symbian OS, VxWorks, Windows CE, Linux, pSOS and QNX Performance 32/64MByte (256/512Mbit) 16MByte (128Mbit) Burst read/write Sustained read Sustained write 20 MB/sec 3.1 MB/sec 1.3 MB/sec 13.3 MB/sec 1.7 MB/sec 0.86 MB/sec Protection and Security-Enabling Features 16-byte Unique Identification (UID) number 6KB user-configurable One Time Programmable (OTP) area Two configurable write and read-protected partitions for data and boot code Hardware data and code protection: Protection key and LOCK# signal Sticky Lock option for boot partition lock Protected Bad-Block Table Boot Capability Programmable Boot Block with XIP capability to replace boot ROM 1KByte for 16/32MByte devices 2KByte for 64MByte devices Download Engine (DE) for automatic download of boot code from Programmable Boot Block Boot capabilities: CPU initialization Platform initialization OS boot Asynchronous Boot mode to boot CPUs that wake up in burst mode The following abbreviations are used in this document: MB for MByte, Mb for Mbit. 93-SR-002-03-8L 1 w w w .d 1 ee sh ta a u. t4 om c 64MByte devices available in BGA 9x12 form factor only. Data Sheet, Rev. 1.7 www..com DiskOnChip Millennium Plus 16/32/64MByte Reliability On-the-fly Reed-Solomon Error Detection Code/Error Correction Code (EDC/ECC) Guaranteed data integrity, even after power failure Transparent bad-block management Dynamic and static wear-leveling Applications Internet set-top boxes, interactive TVs, web browsers WBT, thin clients, network computers PDAs and smart handsets Embedded systems Routers, switches, networking equipment Car PCs, automotive computing Point of sale (POS) terminals, industrial PCs Medical equipment Hardware Compatibility Configurable interface: simple SRAM-like or multiplexed A/D interface Compatible with all major CPUs, including: X86 StrongARM XScale Geode(R) SCxxxx PowerPCTM MPC8xx Dragonball MX1 MediaGX 68K MIPS SuperHTM SH-x All capacities are pinout compatible, in TSOP-I and BGA form factors 8-bit, 16-bit and 32-bit bus architecture support Power Requirements Operating voltage Core: 2.7V to 3.6V I/O (auto-detect): 1.65 - 1.95V or 2.7V - 3.6V (16MB) 2.7V - 3.6V (32/64MB) Current (Typical) Active: 25 mA Deep Power-Down: 10 A (16/32MB) 20 A (64MB) Capacities 16MB (128Mb) with device cascading option for up to 64MB (512Mb) 32MB (256Mb) with device cascading option for up to 128MB (1Gb) 64MB (512Mb) with device cascading option for up to 128MB (1Gb) TrueFFS Software Full hard-disk read/write emulation for transparent file system management Identical software for all DiskOnChip capacities Patented methods to extend flash lifetime, including: Dynamic virtual mapping Dynamic and static wear-leveling Support for all major OS environments, including: Windows CE Linux VxWorks Symbian OS Windows NT PSOS QNX ATI Nucleus DOS Support for OS-less environments 8KB memory window 2 Data Sheet, Rev. 1.7 Packaging 48-pin TSOP-I: 20 x 12 x 1.2 mm 69-ball BGA: 9 x 12 x 1.4 mm (max) 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte Table of Contents 1. 2. Introduction ......................................................................................................................... 7 Product Overview ................................................................................................................ 8 2.1 Product Description ...................................................................................................................... 8 2.2 Standard Interface ........................................................................................................................ 9 2.2.1 Pin and Ball Diagrams .............................................................................................................. 9 2.2.2 System Interface ..................................................................................................................... 10 2.2.3 Signal Descriptions ................................................................................................................. 11 2.3 Multiplexed Interface................................................................................................................... 15 2.3.1 Pin and Ball Diagrams ............................................................................................................ 15 2.3.2 System Interface ..................................................................................................................... 16 2.3.3 Signal Descriptions ................................................................................................................. 17 3. Theory of Operation .......................................................................................................... 21 3.1 Overview..................................................................................................................................... 21 3.2 System Interface......................................................................................................................... 22 3.3 Configuration Interface ............................................................................................................... 23 3.4 Protection and Security-Enabling Features ................................................................................ 23 3.4.1 Read/Write Protection ............................................................................................................. 23 3.4.2 Unique Identification (UID) Number ........................................................................................ 23 3.4.3 One-Time Programmable (OTP) Area .................................................................................... 23 3.5 Programmable Boot Block with eXecute In Place (XIP) Capability............................................ 24 3.6 Download Engine (DE) ............................................................................................................... 24 3.7 Error Detection Code/Error Correction Code (EDC/ECC).......................................................... 24 3.8 Data Pipeline .............................................................................................................................. 25 3.9 Control & Status.......................................................................................................................... 25 3.10 Flash Architecture....................................................................................................................... 25 4. Hardware Protection ......................................................................................................... 27 4.1 Method of Operation ................................................................................................................... 27 4.2 Low Level Structure of Protected Area....................................................................................... 28 5. Modes of Operation........................................................................................................... 29 5.1 Normal Mode .............................................................................................................................. 30 5.2 Reset Mode ................................................................................................................................ 30 5.3 Deep Power-Down Mode ........................................................................................................... 30 6. TrueFFS Technology......................................................................................................... 31 6.1 General Description .................................................................................................................... 31 6.1.1 Built-in Operating System Support.......................................................................................... 31 6.1.2 TrueFFS Software Development Kit (SDK) ............................................................................ 32 6.1.3 File Management .................................................................................................................... 32 6.1.4 Bad-Block Management.......................................................................................................... 32 6.1.5 Wear-Leveling ......................................................................................................................... 32 6.1.6 Power Failure Management.................................................................................................... 33 6.1.7 Error Detection/Correction ...................................................................................................... 33 6.1.8 Special Features through I/O Control (IOCTL) Mechanism.................................................... 33 3 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 6.1.9 Compatibility............................................................................................................................ 33 6.2 8KB Memory Window in DiskOnChip Millennium Plus 16/32MB ............................................... 34 6.3 8KB Memory Window in DiskOnChip Millennium Plus 64MB .................................................... 35 7. Register Descriptions ....................................................................................................... 36 7.1 Definition of Terms...................................................................................................................... 36 7.2 Reset Values .............................................................................................................................. 36 7.3 Chip Identification (ID) Register.................................................................................................. 36 7.4 No Operation (NOP) Register..................................................................................................... 37 7.5 Test Register .............................................................................................................................. 37 7.6 DiskOnChip Control Register/Control Confirmation Register..................................................... 38 7.7 Device ID Select Register........................................................................................................... 39 7.8 Configuration Register ................................................................................................................ 39 7.9 Output Control Register .............................................................................................................. 40 7.10 Interrupt Control.......................................................................................................................... 40 7.11 Toggle Bit Register ..................................................................................................................... 41 8. Booting from DiskOnChip Millennium Plus .................................................................... 42 8.1 Introduction ................................................................................................................................. 42 8.2 Boot Procedure in PC Compatible Platforms ............................................................................. 42 8.3 Boot Replacement ...................................................................................................................... 43 8.3.1 PC Architectures ..................................................................................................................... 43 8.3.2 Non-PC Architectures ............................................................................................................. 43 8.3.3 Using DiskOnChip Millennium Plus in Asynchronous Boot Mode .......................................... 44 9. Design Considerations ..................................................................................................... 45 9.1 Design Environment ................................................................................................................... 45 9.2 System Interface......................................................................................................................... 46 9.2.1 Standard Interface................................................................................................................... 46 9.2.2 Multiplexed Interface ............................................................................................................... 47 9.3 Connecting Signals..................................................................................................................... 47 9.3.1 Standard Interface................................................................................................................... 47 9.3.2 Multiplexed Interface ............................................................................................................... 48 9.4 Implementing the Interrupt Mechanism ...................................................................................... 48 9.4.1 Hardware Configuration .......................................................................................................... 48 9.4.2 Software Configuration ........................................................................................................... 48 9.5 Platform-Specific Issues ............................................................................................................. 49 9.5.1 Wait State................................................................................................................................ 49 9.5.2 Big and Little Endian Systems ................................................................................................ 49 9.5.3 Busy Signal ............................................................................................................................. 49 9.5.4 Working with 8/16/32-Bit Systems with a Standard Interface ................................................. 49 9.6 Device Cascading....................................................................................................................... 51 9.6.1 Standard Interface................................................................................................................... 51 9.6.2 Multiplexed Interface ............................................................................................................... 51 9.7 Memory Map in Cascaded Configuration ................................................................................... 52 4 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 10. Product Specifications ..................................................................................................... 53 10.1 Environmental Specifications ..................................................................................................... 53 10.1.1 Operating Temperature Ranges ............................................................................................. 53 10.1.2 Thermal Characteristics .......................................................................................................... 53 10.1.3 Humidity .................................................................................................................................. 53 10.1.4 Endurance............................................................................................................................... 53 10.2 Disk Capacity.............................................................................................................................. 53 10.3 Electrical Specifications .............................................................................................................. 54 10.3.1 Absolute Maximum Ratings .................................................................................................... 54 10.3.2 Capacitance ............................................................................................................................ 54 10.3.3 DC Electrical Characteristics Over Operating Range ............................................................. 55 10.3.4 AC Operating Conditions ........................................................................................................ 58 10.4 Timing Specifications.................................................................................................................. 59 10.4.1 Read Cycle Timing Standard Interface ................................................................................... 59 10.4.2 Write Cycle Timing Standard Interface ................................................................................... 62 10.4.3 Read Cycle Timing Multiplexed Interface ............................................................................... 64 10.4.4 Write Cycle Timing Multiplexed Interface ............................................................................... 65 10.4.5 Power-Up Timing .................................................................................................................... 66 10.4.6 Interrupt Timing ....................................................................................................................... 67 10.5 Mechanical Dimensions.............................................................................................................. 68 11. Ordering Information......................................................................................................... 70 5 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte Revision History Revision 1.7 Date February 2003 Description ID[0:1], AVD# and VCCQ - description detailed Absolute maximum ratings table updated to reflect limitations when applying separate VCCQ/VCC on 16MB devices Capacitance table for dual-die devices added Ordering info table updated to reflect Pb-free ordering info Reference Sections 2.2.3 and 2.3.3 Section 10.3.1 Section 10.3.2 Section 11 6 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 1. Introduction Overview of data sheet contents Product overview, including a brief product description, pin and ball diagrams and signal descriptions Theory of operation for the major building blocks Hardware Protection mechanism Modes of operation TrueFFS Technology, including power failure management and 8Kbyte memory window Register Description Using DiskOnChip Millennium Plus as a boot device Hardware and software design considerations Environmental, electrical, timing and product specifications Information on ordering DiskOnChip Millennium Plus Example code to verify DiskOnChip Millennium Plus operation This data sheet includes the following sections: Section 1: Section 2: Section 3: Section 4: Section 5: Section 6: Section 7: Section 8: Section 9: Section 10: Section 11: Appendix A: To contact M-Systems' worldwide offices for general information and technical support, please see the listing on the back cover, or visit M-Systems' website (www.m-sys.com). 7 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 2. 2.1 Product Overview Product Description DiskOnChip Millennium Plus is a member of M-Systems' DiskOnChip product series. A single die (16/32MB) or dual die (64MB) with embedded flash controller and flash memory, DiskOnChip Millennium Plus provides a complete, easily integrated flash disk for highly reliable data and code storage. DiskOnChip Millennium Plus also offers advanced features for hardware-protected data and code and security-enabling features for both data and code storage. Available in two form factors, a 48-pin Thin Small Outline Package (TSOP-I) and a 69-ball Ball Grid Array (BGA), and in capacities of 16MB (128Mb), 32MB (256Mb) and 64MB (512Mb), DiskOnChip Millennium Plus is optimized for applications that require data and code storage, the industry's highest reliability, exceptional performance and minimum size. These include set-top boxes (STBs), handsets, personal digital assistants (PDAs), thin clients, telecommunication applications and embedded systems. DiskOnChip Millennium Plus protection and security-enabling features offer a number of benefits. Two write and read-protected partitions, with both software and hardware-based protection, can be configured independently for maximum design flexibility. The 16-byte Unique ID (UID) identifies each flash device used with security and authentication applications, eliminating the need for a separate ID device (i.e. EEPROM) on the motherboard. The user-configurable One Time Programmable (OTP) area, written to once and then locked to prevent data and code from being altered, is ideal for storing customer and product-specific information. In addition, the Bad Block Table is hardware-protected, ensuring that it will not be damaged or accidentally changed to ensure maximum reliability. DiskOnChip Millennium Plus devices have a simple SRAM-like interface, for easy integration. DiskOnChip Millennium Plus 16MB devices can also be configured to work with a multiplexed interface. Multiplexing data and address lines can save board space, reduce RF noise effects and more. DiskOnChip Millennium Plus is based on Toshiba's cutting-edge 0.16 NAND flash technology. This technology enables DiskOnChip Millennium Plus to provide unmatched physical and performance-related benefits. It has the highest flash density in the smallest die size available on the market, for the best cost structure and the smallest real estate. DiskOnChip Millennium Plus 32/64MB devices use 16-bit internal flash access, featuring unrivaled write and read performance. M-Systems' patented TrueFFS software technology fully emulates a hard disk to manage the files stored on DiskOnChip Millennium Plus. This transparent file system management enables read/write operations that are identical to a standard, sector-based hard disk. In addition, TrueFFS employs various patented methods, such as dynamic virtual mapping, dynamic and static wear-leveling, and automatic bad block management to ensure high data reliability and to maximize flash lifetime. TrueFFS binary drivers are available for a wide range of popular OSs, including Symbian OS, VxWorks, Windows CE/.NET, Linux, and QNX. Customers developing for target platforms not supported by TrueFFS binary drivers can use the TrueFFS Software Development Kit (SDK). For customized boot solutions, M-Systems provides the Boot Software Development Kit (BDK). DiskOnChip Millennium Plus is a cost-effective solution for code storage as well as data storage. A Programmable Boot Block with eXecute In Place (XIP) capability can store boot code, replacing the boot ROM to function as the only non-volatile memory on board. This reduces hardware expenditures and board real estate. The Programmable Boot Block for 16/32MB devices is 1KB in size, and for 64MB devices it is 2KB in size. M-Systems' Download Engine (DE) is an automatic bootstrap mechanism that expands the functionality of the programmable boot block to enable CPU and platform initialization directly from DiskOnChip Millennium Plus. DiskOnChip Millennium Plus is designed for compatibility and easy scalability. All capacities are drop-in replacements for the same package, either TSOP-I or BGA. Greater capacities may easily be obtained by cascading up to four devices with no additional glue logic. This upgrade path provides a flash disk of up to 128MB (1Gb), while remaining totally transparent to the file system and user. 8 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 2.2 Standard Interface 2.2.1 Pin and Ball Diagrams See Figure 1 for the DiskOnChip Millennium Plus standard interface TSOP-I pin diagram and Figure 2 for the BGA ball diagram. To ensure proper device functionality, pins/balls marked RSRVD are reserved for future use and should not be connected. Pins/balls marked RSRVD1 require a pull-up resistor. RSTIN# CE# WE# OE# A12 A11 A10 A9 A8 A7 A6 VCC VSS A5 A4 A3 A2 A1 A0 BHE# RSRVD IF_CFG LOCK# ID0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 VSS IRQ# D15 D14 D13 D12 D11 D10 D9 D8 RSRVD VCCQ VSS D7 D6 D5 D4 D3 D2 D1 D0 BUSY# ID1 VSS DiskOnChip Millennium Plus 48-pin TSOP-I Package Figure 1: Standard Interface TSOP-I Pinout (Top View) 1 A B C D E F G H J K L M M M A 2 3 4 5 6 7 8 9 10 M M M A7 RSRVD RSRVD WE# A8 A11 A3 A6 RSRVD RSTIN# RSRVD RSRVD A12 RSRVD A2 A5 BHE# BUSY# RSRVD A9 LOCK# RSRVD M A1 A4 IF_CFG A10 ID0 IRQ# M M A0 VSS D1 D6 RSRVD ID1 M CE# OE# D9 D3 D4 D13 D15 RSRVD RSRVD D0 D10 VCC VCCQ D12 D7 VSS D8 D2 D11 RSRVD D5 D14 M M M Figure 2: Standard Interface BGA Ball Diagram (Top View) 9 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 2.2.2 System Interface See Figure 3 for a simplified I/O diagram for a standard interface. CE#, OE#, WE# A[12:0] Host SystemBus BHE# D[15:0] RSTIN# DiskOnChip MillenniumPlus BUSY# IRQ# ID[1:0] SystemInterface IF_CFG Configuration LOCK# Control Figure 3: Standard Interface Simplified I/O Diagram 10 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 2.2.3 Signal Descriptions DiskOnChip Millennium Plus TSOP-I and BGA packages support identical signals. The related pin and ball designations are listed in the signal descriptions, presented in logic groups, in Table 1 and Table 2. TSOP-I Package Table 1: Standard Interface Signal Descriptions, TSOP-I Package Signal Pin No. Input Type ST Address bus. Description System Interface A[12:6] A[5:0] BHE# 5-11 14-19 20 Input Input Signal Type ST, R8 Byte High Enable, active low. When low, data transaction on D[15:8] is enabled. Not used and may be left floating when IF_CFG is set to 0 (8-bit mode). ST, R Chip Enable, active low. IN Data bus, low byte. CE# D[7:0] D[15:8] OE# WE# ID[1:0] 2 35-28 46-39 4 3 26, 24 Input Input/ Output Input Input Input Input IN, R8 Data bus, high byte. Not used and may be left floating when IF_CFG is set to 0 (8-bit mode). ST ST ST Output Enable, active low. Write Enable, active low. Configuration Identification. For DiskOnChip 16MB/32MB, up to four chips can be cascaded in the same memory window, according to the following assignment: Chip 1 = ID1, ID0 = VSS, VSS (0,0); required for single chip Chip 2 = ID1, ID0 = VSS, VCC (0,1) Chip 3 = ID1, ID0 = VCC, VSS (1,0) Chip 4 = ID1, ID0 = VCC, VCC (1,1) For DiskOnChip 64MB, up to two chips can be cascaded in the same memory window, according to the following assignment: Chip 1 = ID1=VSS, ID0 = VSS; required for single chip Chip 2 = ID1=VSS, ID0 = VCC Interface Configuration, 1 for 16-bit interface mode, 0 for 8-bit interface mode. Lock, active low. When active, provides full hardware data protection of selected partitions. Control Busy, active low, open drain. Indicates that DiskOnChip is initializing and should not be accessed. A 10 K pull-up resistor is required even if the pin is not used. Interrupt Request. Requires a 10 K pull-up resistor. Reset, active low. IF_CFG LOCK# 22 23 ST ST Input Input BUSY# 27 OD Output IRQ# RSTIN# 47 1 ST Output Input 11 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte Signal Pin No. Input Type Power - Description Signal Type Supply VCCQ 37 I/O power supply. Requires a 10 nF and 0.1 F capacitor. For 16MB devices, VCCQ may be either 2.7V to 3.6V or 1.65V to 1.95V. For 32/64MB devices, VCCQ is 2.7V to 3.6V Device supply. All VCC pins must be connected. Requires a 10 nF and 0.1 F capacitor. Ground. All VSS pins must be connected. Reserved VCC VSS 12 13, 25, 36, 48 21 - Supply Supply RSRVD - Reserved signal that is not connected internally and must be left floating to guarantee forward compatibility with future products. It should not be connected to arbitrary signals. Reserved signal that is not connected internally. Note: Future DiskOnChip devices will use this pin as a clock input. To be forward compatible, this pin can already be connected to the system CLK or to VCC when the clock input feature is not required. 38 - The following abbreviations are used: IN Standard (non-Schmidt) input ST Schmidt Trigger input OD Open drain R8 Nominal 22 K pull-up resistor, enabled only for 8-bit interface mode (IF_CFG input is 0) R 3.7 M nominal pull-up resistor Note: For forward compatibility with future DiskOnChip 7x10 BGA products, additional pads are required. Please refer to application note AP-DOC-067, Preparing Your PCB Footprint for the DiskOnChip BGA Migration Path, for detailed information. Note: DiskOnChip Millennium Plus 64MB devices are not available in a TSOP-I package. 12 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte BGA Package Table 2: Standard Interface Signal Descriptions, BGA Package Signal Ball No. Input Type ST Description System Interface Address bus. Signal Type Input A[12:11] A[10:8] A[7:4] A[3:0] BHE# D8, C8 F7, E7, C7 C3, D3, E3, F3 D2, E2, F2, G2 E4 ST, R8 Byte High Enable, active low. When low, data transaction on D[15:8] is enabled. Not used and may be left floating when IF_CFG is set to 0 (8-bit mode). ST, R Chip Enable, active low. IN Data bus, low byte. Input CE# D[7:0] D[15:8] OE# WE# ID[1:0] H2 J8, G7, K7, H6, H5, K4, G4, J3 H8, K8, H7, J7, K5, J4, H4, K3 H3 C6 G9, F8 Input Input/ Output Input Input Input Input IN, R8 Data bus, high byte. Not used and may be left floating when IF_CFG is set to 0 (8-bit mode). ST ST ST Output Enable, active low Write Enable, active low Configuration Identification. For DiskOnChip 16MB/32MB, up to four chips can be cascaded in the same memory window, according to the following assignment: Chip 1 = ID1, ID0 = VSS, VSS (0,0); required for single chip Chip 2 = ID1, ID0 = VSS, VCC (0,1) Chip 3 = ID1, ID0 = VCC, VSS (1,0) Chip 4 = ID1, ID0 = VCC, VCC (1,1) For DiskOnChip 64MB, up to two chips can be cascaded in the same memory window, according to the following assignment: Chip 1 = ID1=VSS, ID0 = VSS; required for single chip Chip 2 = ID1=VSS, ID0 = VCC Interface Configuration, 1 for 16-bit interface mode, 0 for 8-bit interface mode. Lock, active low. When active, provides full hardware data protection of selected partitions. IF_CFG LOCK# F4 E8 ST ST Input Input BUSY# E5 OD Control Busy, active low, open drain. Indicates that DiskOnChip is Output initializing and should not be accessed. A 10 K pull-up resistor is required even if the ball is not used. Interrupt Request. Requires a 10 K pull-up resistor. Reset, active low. Input Input IRQ# RSTIN# VCCQ F9 D5 J6 ST Power I/O power supply. Requires a 10 nF and a 0.1 F capacitor. Supply For 16MB devices, VCCQ may be either 2.7V to 3.6V or 1.65V to 1.95V. For 32/64MB devices, VCCQ is 2.7V to 3.6V Device supply. Requires a 10 nF and 0.1 F capacitor. Data Sheet, Rev. 1.7 VCC 13 J5 Supply 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte Signal VSS RSRVD Ball No. G3, J9 K6 Input Type - Description Ground. All VSS balls must be connected. Reserved Reserved signal that is not connected internally. Note: Future DiskOnChip devices will use this pin as a clock input. To be forward compatible, this pin can already be connected to the system CLK or to VCC when the clock input feature is not required. Signal Type Supply Other. See Figure 2 - All reserved signals are not connected internally and must be left floating to guarantee forward compatibility with future products. They should not be connected to arbitrary signals. Mechanical Mechanical. These balls are for mechanical placement, and are not connected internally. Alignment. This ball is for device alignment, and is not connected internally - M A - The following abbreviations are used: IN Standard (non-Schmidt) input ST Schmidt Trigger input OD Open drain R8 Nominal 22 K pull-up resistor, enabled only for 8-bit interface mode (IF_CFG input is 0) R 3.7 M nominal pull-up resistor Note: For forward compatibility with future DiskOnChip 7x10 BGA products, additional pads are required. Please refer to application note AP-DOC-067, Preparing Your PCB Footprint for the DiskOnChip BGA Migration Path, for detailed information. 14 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 2.3 Multiplexed Interface 2.3.1 Pin and Ball Diagrams See Figure 4 for the DiskOnChip Millennium Plus 16MB multiplexed interface TSOP-I pin diagram and Figure 5 for the BGA ball diagram. To ensure proper device functionality, pins/balls marked RSRVD are reserved for future use and should not be connected. Pins/balls marked RSRVD1 require a pull-up resistor. RSTIN# CE# WE# OE# VSS VSS VSS VSS VSS VSS VSS VCC VSS VSS VSS VSS VSS VSS VSS VSS RSRVD VCC LOCK# ID0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 VSS IRQ# AD15 AD14 AD13 AD12 AD11 AD10 AD9 AD8 RSRVD VCCQ VSS AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 BUSY# AVD# VSS DiskOnChip Millennium Plus 48-pin TSOP-I Package Figure 4: Multiplexed Interface TSOP-I Pinout (Top View) 1 A M 2 3 4 5 6 7 8 9 10 M B M A VSS RSRVD RSRVD WE# VSS VSS M C D VSS VSS RSRVD RSTIN# RSRVD RSRVD VSS RSRVD E M VSS VSS VSS BUSY# RSRVD VSS LOCK# RSRVD F VSS VSS VCCQ VSS ID0 IRQ# G H M VSS VSS AD1 AD6 RSRVD AVD# CE# OE# AD9 AD3 AD4 AD13 AD15 RSRVD J RSRVD AD0 AD10 VCC VCCQ AD12 AD7 VSS K M AD8 AD2 AD11 RSRVD AD5 AD14 L M M M M Figure 5: Multiplexed Interface BGA Ball Diagram (Top View) Note: 15 DiskOnChip Millennium Plus 16MB devices only support the multiplexed interface. Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 2.3.2 System Interface See Figure 6 for a simplified I/O diagram. CE#, OE#, WE# Host System Bus AD[15:0] RSTIN# DiskOnChip Millennium Plus BUSY# IRQ# ID0 System Interface AVD# Configuration LOCK# Control Figure 6: Multiplexed Interface Simplified I/O Diagram 16 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 2.3.3 Signal Descriptions TSOP-I Package DiskOnChip Millennium Plus 16MB TSOP-I and BGA packages support the identical signals in multiplexed interface. The related pin and ball designations are listed in the signal descriptions, presented in logic groups, in Table 3 and Table 4. Table 3: Multiplexed Interface Signal Descriptions, TSOP-I Package Signal Pin No. Input Type ST Description System Interface AD[15:0] CE# OE# WE# AVD# ID0 46-39, 35-28 2 4 3 26 24 Multiplexed bus. Address and data signals. Input/ Output Input Input Input Input Input Signal Type ST, R Chip Enable, active low. ST ST ST ST Output Enable, active low. Write Enable, active low. Configuration Sets multiplexed interface. Multiplexed mode is entered when a rising edge is detected on this pin/ball. Identification. For DiskOnChip Millennium Plus 16MB, up to two chips can be cascaded in the same memory window, according to the following assignment: Chip 1 = ID0 = VSS; must be used for single chip configuration Chip 2 = ID0 = VCC Lock, active low. When active, provides full hardware data protection of selected partitions. Control Busy, active low, open drain. Indicates that DiskOnChip is initializing and should not be accessed. A 10 K pull-up resistor is required even if the pin is not used. Interrupt Request. Requires a 10 K pull-up resistor. Reset, active low. Power I/O power supply. Requires a 10 nF and a 0.1 F capacitor. For 16MB devices, VCCQ may be either 2.7V to 3.6V or 1.65V to 1.95V. For 32/64MB devices, VCCQ is 2.7V to 3.6V Device supply. All VCC pins must be connected; each VCC pin requires a 10 nF and 0.1 F capacitor. Ground. All VSS pins must be connected. Reserved LOCK# 23 ST Input BUSY# 27 OD Output IRQ# RSTIN# VCCQ 47 1 37 ST - Output Input Supply VCC VSS 12, 22 5-11, 13-20, 25, 36, 48 21 - Supply Supply RSRVD - Reserved signal that is not connected internally and must be left floating to guarantee forward compatibility with future products. It should not be connected to arbitrary signals. 17 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte Signal Pin No. 38 Input Type - Description Reserved signal that is not connected internally. Note: Future DiskOnChip devices will use this pin as a clock input. To be forward compatible, this pin can already be connected to the system CLK or to VCC when the clock input feature is not required. Signal Type The following abbreviations are used: IN Standard (non-Schmidt) input ST Schmidt Trigger input OD Open drain R8 Nominal 22 K pull-up resistor, enabled only for 8-bit interface mode (IF_CFG input is 0) R 3.7 M nominal pull-up resistor 18 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte BGA Package Table 4: Multiplexed Interface Signal Descriptions, BGA Package Signal Ball No. Input Type IN Description System Interface AD[15:12] AD[11:8] AD[7:4] AD[3:0] CE# OE# WE# AVD# ID0 H8, K8, H7, J7, K5, J4, H4, K3, J8, G7, K7, H6, H5, K4, G4, J3 H2 H3 C6 G9 F8 Multiplexed bus. Address and data signals. Input/ Output Signal Type ST, R Chip Enable, active low. ST ST ST ST Output Enable, active low. Write Enable, active low. Configuration Sets multiplexed interface. Multiplexed mode is entered when a rising edge is detected on this pin/ball. Input Input Input Input Identification. For DiskOnChip Millennium Plus 16MB, up to two Input chips can be cascaded in the same memory window, according to the following assignment: Chip 1 = ID0 = VSS; must be used for single chip configuration Chip 2 = ID0 = VCC Lock, active low. When active, provides full hardware data protection of selected partitions. Control Input LOCK# E8 ST BUSY# E5 OD Busy, active low, open drain. Indicates that DiskOnChip is Output initializing and should not be accessed. A 10 K pull-up resistor is required even if the ball is not used. Interrupt Request. Requires a 10 K pull-up resistor. Reset, active low. Power Output Input IRQ# RSTIN# VCCQ F9 D5 F4, J6 ST I/O power supply. Requires a 10 nF and a 0.1 F capacitor. Supply For 16MB devices, VCCQ may be either 2.7V to 3.6V or 1.65V to 1.95V. For 32/64MB devices, VCCQ is 2.7V to 3.6V Device supply. All VCC balls must be connected; each VCC ball requires a 10 nF and a 0.1 F capacitor. Ground. All VSS balls must be connected. Supply Supply VCC VSS J5 C3, C7, C8, D2, D3, D8, E2, E3, E4, E7, F2, F3, F7, G2, G3, J9 19 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte Signal Ball No. Input Type Reserved - Description Signal Type RSRVD K6 Reserved signal that is not connected internally. Note: Future DiskOnChip devices will use this pin as a clock input. To be forward compatible, this pin can already be connected to the system CLK or to VCC when the clock input feature is not required. Other. See Figure 5 - Reserved signal that is not connected internally and must be left floating to guarantee forward compatibility with future products. It should not be connected to arbitrary signals. Mechanical Mechanical. These balls are for mechanical placement, and are not connected internally. Alignment. This ball is for device alignment, and is not connected internally. - M A - The following abbreviations are used: IN Standard (non-Schmidt) input ST Schmidt Trigger input OD Open drain R8 Nominal 22 K pull-up resistor, enabled only for 8-bit interface mode (IF_CFG input is 0) R 3.7 M nominal pull-up resistor Note: For forward compatibility with future DiskOnChip 7x10 BGA products, additional pads are required. Please refer to Application Note AP-DOC-067, Preparing your PCB Footprint for the DiskOnChip BGA Migration Path, for detailed information. 20 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 3. 3.1 * * * * * * * * Theory of Operation Overview System Interface for host interface Configuration Interface for configuring the DiskOnChip to operate in 8/16 bit mode, cascaded configuration and hardware write protection. Protection and Security-Enabling containing read/write protection and One-Time Programming (OTP), for advanced data/code security and protection Programmable Boot Block with XIP capability enhanced with a Download Engine (DE) for system initialization capability Reed-Solomon-based Error Detection and Error Correction Code (EDC/ECC) for on-the-fly error handling Data Pipeline through which the data flows from the system to the NAND flash arrays. Control & Status block that contains registers responsible for transferring the address, data and control information between the TrueFFS driver and the flash media. Flash Interface whose architecture depends on the capacity: 32MB (256Mb) and 64MB2 (512Mb) implements a unique interleaved, dual bank architecture of two embedded 16MB NAND flash arrays (Figure 7); 16MB uses a single NAND flash array (Figure 8). Bus Control for translating the host bus address, data and control signals into valid NAND flash signals. Address Decoder to enable the relevant unit inside DiskOnChip controller, according to the address range received from the system interface. DiskOnChip Millennium Plus consists of the following major functional blocks, as shown in Figure 7 and Figure 8. * * Figure 7: Standard Interface Simplified Block Diagram, 32/64MB Devices 2 DiskOnChip Millennium Plus 64MB consists of two stacked DiskOnChip Millennium Plus 32MB devices in a dual-die package. Data Sheet, Rev. 1.7 93-SR-002-03-8L 21 DiskOnChip Millennium Plus 16/32/64MByte Figure 8: Standard Interface Simplified Block Diagram, 16MB Devices 3.2 System Interface The system interface block provides an easy-to-integrate SRAM-like (also EEPROM-like) interface to DiskOnChip Millennium Plus, enabling it to interface with various CPU interfaces, such as a local bus, ISA bus, SRAM interface, EEPROM interface or any other compatible interface. In addition, the EEPROM-like interface enables direct access to the Programmable Boot Block to permit XIP functionality during system initialization. A 13-bit wide address bus enables access to the DiskOnChip 8KB memory window (as shown in Section 6.2). In 32/64MB capacities, the 16-bit data bus permits full 16-bit wide access to the flash, due to an internal, dual-bank, interleaved architecture. With both internal and external 16-bit access, DiskOnChip Millennium Plus 32/64MB provides unrivaled performance. In 16MB capacities, an 8-bit data bus permits 8-bit wide internal access to the flash but 16-bit external access to the host. The Chip Enable (CE#), Write Enable (WE#) and Output Enable (OE#) signals trigger read and write cycles. A write cycle occurs while both the CE# and the WE# inputs are asserted. Similarly, a read cycle occurs while both the CE# and OE# inputs are asserted. Note that DiskOnChip Millennium Plus does not require a clock signal. DiskOnChip Millennium Plus features a unique analog static design, optimized for minimal power consumption. The CE#, WE# and OE# signals trigger the controller (e.g., system interface block, bus control and data pipeline) and flash access. The Reset In (RSTIN#) and Busy (BUSY#) control signals are used in the reset phase. See Section 5.2 for further details. The Interrupt Request (IRQ#) signal can be used when long I/O operations, such as Block Erase, delay the CPU resources. The signal is also asserted when a Data Protection violation has occurred. When this signal is implemented, the CPU can run other tasks and only returns to continue read/write operations with DiskOnChip Millennium Plus after the IRQ# signal has been asserted and an Interrupt Handling Routine (implemented in the OS) has been called to return control to the TrueFFS driver. DiskOnChip Millennium Plus contains several configuration signals. The identification signals (ID[1:0]) are used for identifying the relevant DiskOnChip device in a cascaded configuration (see Section 9.6 on cascading for further details). The Lock (LOCK#) signal enables hard-wire hardware-controlled protection of code and data, as described below on protection and security-enabling features. For a standard interface, the Interface Configuration (IF_CFG) signal configures DiskOnChip for 16-bit or 8-bit data access (see Section 9.5.4). 22 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 3.3 Configuration Interface The Configuration Interface block enables the designer to configure DiskOnChip Millennium Plus to operate in different modes. When using a standard interface, the IF_CFG pin/ball is used to configure the device for 8/16 bit access mode. The ID[1:0] pins/balls (only ID0 for a multiplexed interface) are used in cascaded configuration (refer to Section 9.6), and the LOCK# pin/ball is used for hardware write/read protection. 3.4 Protection and Security-Enabling Features The Protection and Security-Enabling block, consisting of read/write protection, Unique ID and OTP area, enables advanced data and code security and protection. Located on the main route of traffic between the host and the flash, this block monitors and controls all data and code transactions to and from DiskOnChip Millennium Plus. 3.4.1 Read/Write Protection Data and code protection is implemented through a Protection State Machine (PSM). The user can configure one or two independently programmable areas of the flash memory as read protected, write protected, or read/write protected. A protection area may be protected by either/both of these hardware mechanisms: * * 64-bit protection key Hard-wired LOCK# signal The size and location of each area is user-defined to provide maximum flexibility for the target platform and application requirements. The configuration parameters of the protected areas are stored on the flash media and are automatically downloaded from the flash to the PSM upon power-up, to enable robust protection throughout the flash lifetime. In the event of an attempt to bypass the protection mechanism, illegally modify the protection key or in any way sabotage the configuration parameters, the entire DiskOnChip becomes both read and write protected, and is completely inaccessible. For further information on the hardware protection mechanism, refer to Section 4. 3.4.2 Unique Identification (UID) Number Each DiskOnChip Millennium Plus is assigned a 16-byte UID number. Burned onto the flash during production, the UID cannot be altered and is unique worldwide. The UID is essential in security-related applications, and can be used to identify end-user products in order to fight fraudulent duplication by imitators. The UID on DiskOnChip Millennium Plus eliminates the need for an additional on-board ID device, such as a dedicated EEPROM. 3.4.3 One-Time Programmable (OTP) Area The 6KB OTP area is user-programmable for complete customization. The user can write to this area once, after which it is automatically locked permanently. After it is locked, the OTP area becomes read only, just like a ROM device. Typically, the OTP area is used to store customer and product information such as: product ID, software version, production data, customer ID and tracking information. 23 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 3.5 Programmable Boot Block with eXecute In Place (XIP) Capability During boot, code must be executed directly from the flash media, rather than first copied to the host RAM and then executed from there. This direct XIP code execution capability is essential for booting. The Programmable Boot Block with XIP capability enables DiskOnChip Millennium Plus to act as a boot ROM device in addition to being a flash disk. This unique design enables the user to benefit from the advantages of NOR flash, typically used for boot and code storage, and NAND flash, typically used for data storage. No other boot device is required on the motherboard. The Programmable Boot Block on DiskOnChip Millennium Plus 16/32MB consists of 1KB of programmable boot block, and DiskOnChip 64MB provides a 2KB Programmable Boot Block. The Download Engine (DE) described in the next section expands the functionality of this block by copying the boot code from the flash into the boot block. When two, three or four DiskOnChip Millennium Plus devices are cascaded, the Programmable Boot Block is respectively accumulated, providing 2, 3 or 4KB of boot block. The Programmable Boot Block of each device is mapped to a unique address space. Note: Up to two DiskOnChip Millennium Plus 64MB devices can be cascaded, providing a Programmable Boot Block of 4KB. 3.6 Download Engine (DE) Upon power up or when the RSTIN# signal is asserted high, the DE automatically downloads the Initial Program Loader from the flash to the Programmable Boot Block. The Initial Program Loader (IPL) is responsible for starting the boot process. The download process is quick (1.3 ms max) and is designed so that when the CPU accesses DiskOnChip for code execution, the IPL code is already located in the Programmable Boot Block. In addition, the DE downloads the Data Protection Structures (DPS) from the flash to the Protection State Machines (PSMs), so that DiskOnChip is secure and protected from the first moment it is active. During the download process, DiskOnChip Millennium Plus asserts the BUSY# signal to indicate to the system that it is not yet ready to be accessed. Once BUSY# is negated, the system can access the DiskOnChip Millennium Plus. A failsafe mechanism prevents improper initialization due to a faulty VCC or invalid assertion of the RSTIN# input. Another failsafe mechanism is designed to overcome possible NAND flash data errors. It prevents internal registers from powering up in a state that bypasses the intended data protection. In addition, in any attempt to sabotage the data structures causes the entire DiskOnChip Millennium Plus to become both read and write-protected and completely inaccessible. 3.7 Error Detection Code/Error Correction Code (EDC/ECC) NAND flash, being an imperfect memory, requires error handling. DiskOnChip Millennium Plus implements Reed-Solomon Error Detection Code (EDC). A hardware-generated, 6-byte error detection signature is computed each time a page (512 bytes) is written to or read from DiskOnChip. The TrueFFS driver implements complementary Error Correction Code (ECC). Unlike error detection, which is required on every cycle, error correction is relatively seldom required, hence implemented in software. The combination of DiskOnChip built-in EDC mechanism and the TrueFFS driver ensures highly reliable error detection and correction, while providing maximum performance. The following detection and correction capability is provided for each 512 bytes: * * * * Corrects up to two 10-bit symbols, including two random bit errors. Corrects single bursts up to 11 bits. Detects single bursts up to 31 bits and double bursts up to 11 bits. Detects up to 4 random bit errors. 24 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 3.8 Data Pipeline DiskOnChip Millennium Plus uses a two-stage pipeline mechanism, designed for maximum performance while enabling on-the-fly data manipulation, such as read/write protection and Error Detection/Error Correction. 3.9 Control & Status The Control & Status block contains registers responsible for transferring the address, data and control information between the DiskOnChip TrueFFS driver and the flash media. Additional registers are used to monitor the status of the flash media (ready/busy) and of the DiskOnChip controller. For further information on the DiskOnChip Millennium Plus registers, refer to Section 7). 3.10 Flash Architecture A 16MB flash bank consists of 1024 blocks organized in 32 pages, as follows: * Page - Each page contains 512 bytes of user data and a 16-byte extra area that is used to store flash management and EDC/ECC signature data, as shown in Figure 9. A page is the minimal unit for read/write operations. Block - Each block contains 32 pages (total of 16KB), as shown in Figure 10. A block is the minimal unit that can be erased, and is sometimes referred to as an erase block. Flash Management & ECC/EDC Signature 16 Bytes * User Data 512 Bytes 0.5 KB Figure 9: Page Structure 512 Bytes 16 Bytes Page 0 Page 1 16 KB Page 30 Page 31 Figure 10: Block Structure 16MB DiskOnChip Millennium Plus devices are designed with a single-bank 16MB flash array, consisting of 1024 blocks organized in 32 pages. 32MB DiskOnChip Millennium Plus devices are designed with a dual-bank interleave architecture, consisting of two banks of 16MB NAND flash. The interleave architecture allows 16-bit internal flash access instead of the standard 8-bit flash access, thereby providing double the performance for read, write and erase operations. The interleave architecture consist of 1024 dual blocks organized in 32 dual pages, for a total capacity of 32MB, as shown in Figure 11. 25 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 64MB DiskOnChip Millennium Plus devices are dual-die devices, consisting of two stacked 32MB devices. Therefore, the interleave architecture, block and page size are similar to that of DiskOnChip Millennium Plus 32MB devices. Interleaving of Dual Pages in Dual Blocks Block 0 (16 KB) Block 1024 (16KB) Block 1022 (16 KB) Block 1023 (16 KB) Block 2045 (16 KB) Block 2046 (16 KB) Figure 11: Interleave Architecture Structure 26 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 4. 4.1 Hardware Protection Method of Operation DiskOnChip Millennium Plus enables the user to define two partitions that are protected (in hardware) against any combination of read or write operations. The two protected areas can be configured as read protected or writeprotected, and are protected by a protection key (i.e. password) defined by the user. Each of the protected areas can be configured separately and can function separately, providing maximal flexibility for the user. The size and protection attributes (protection key/read/write/changeable/lock) of the protected partition are defined in the media formatting stage (DFORMAT utility or the format function in the TrueFFS SDK). In order to set or remove a read/write protection, the protection key (i.e., password) must be used, as follows: * * Insert the protection key to remove read/write protection. Remove the protection key to set read/write protection. DiskOnChip Millennium Plus has an additional hardware safety measurement. If the Lock option is enabled (by means of software) and the LOCK# pin/ball is asserted, the protected partition has an additional hardware lock that prevents read/write access to the partition, even with the use of the correct protection key. The LOCK# pin/ball must be asserted during DFORMAT (and later when the partition is defined as changeable) to enable the additional hard-wired safety lock. It is possible to set the Lock option for one session only, that is, until the next power-up or reset. This Sticky Lock feature can be useful when the boot code in the boot partition must be read/write protected. Upon power-up, the boot code must be unprotected so the CPU can run it directly from DiskOnChip. At the end of the boot process, protection can be set until the next power-up or reset. Setting the Sticky Lock (SLOCK) bit in the Output Control Register to 1 has the same effect as asserting the LOCK# pin. Once set, SLOCK can only be cleared by asserting the RSTIN# input. Like the LOCK# input, the assertion of this bit prevents the protection key from disabling the protection for a given partition. For more information, see Section 7.9. The target partition does not have to be mounted before calling a hardware protection routine. Note: The Sticky Lock feature is only supported in 16MB devices. Only one partition can be defined as "changeable"; i.e., its password and attributes are fully configurable at any time (from read to write, both or none and visa versa). Note that "un-changeable" partition attributes cannot be changed unless the media is reformatted. A change of any of the protection attributes causes a reset of the protection mechanism and consequently the removal of all device protection keys. That is, if the protection attributes of one partition are changed, the other partition will lose its key-protected read/write protection. The only way to read or write from a read or write protected partition is to use the insert key call (even DFORMAT does not remove the protection). This is also true for modifying its attributes (key, read, write and lock enable state). Read/write protection is disabled in each one of the following events: * * * * Power-down Change of any protection attribute (not necessarily in the same partition) Write operation to the IPL area Removal of the protection key. For further information on hardware protection, please refer to the TrueFFS Software Development Kit (SDK) developer guide or application note AP-DOC-057, Protection and Security-Enabling Features in DiskOnChip Plus. 27 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 4.2 Low Level Structure of Protected Area The first three blocks on DiskOnChip Millennium contain foundry information, the Data Protect structures, Initial Program Loader (IPL) code, and bad block mapping information. See Figure 12. Bad Block Table and Factory-Programmed UID Pages 0-5 Block 0 OTP Pages 7-12 Data Protect Structure 0 Block 1 Data Protect Structure 1 and IPL Code Block 2 Figure 12: Low Level Format DiskOnChip Millennium Plus Blocks 0, 1 and 2 in DiskOnChip Millennium Plus contain the following information: Block 0 * * * * Bad Block Table (page 2). Contains the mapping information to unusable erase units on the flash media. UID (16 bytes). This number is written during the manufacturing stage, and cannot be altered at a later time. Customer OTP (occupies pages 26-31). The OTP area is written once and then locked. Data Protect Structure 0. This structure contains configuration information on one of the two user-defined protected partitions. Data Protect Structure 1. This structure contains configuration information on one of the two user-defined protected partitions. IPL Code (1KB). This is the boot code that is downloaded by the DE to the internal boot block. Block 1 Block 2 * * 28 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 5. * * * * * * * * * Modes of Operation Reset Normal Deep Power-Down. Assertion of the RSTIN# signal sets the device in Reset mode. During power-up, boot detector circuitry sets the device in Reset mode. A valid write sequence to DiskOnChip sets the device in Normal mode. This is done automatically by the TrueFFS driver on power-up (Reset sequence end). Switching back from Normal mode to Reset mode can be done by a valid write sequence to DiskOnChip, or by triggering the boot detector circuitry (by soft reset). Power-down. A valid write sequence, initiated by software, sets the device from Normal mode to Deep Power-Down mode. Four read cycles from offset 0x1FFF set the device back to Normal mode. Alternately, the device can be set back to Normal mode with an extended access time during a read from the Programmable Boot Block (see Section 10.4.1 for read cycle timing). Asserting the RSTIN# signal and holding it in this state while in Normal mode puts the device in Deep Power-Down mode. When the RSTIN# signal is released, the device is set in Reset mode. (This is shown in the diagram as the dotted arrow.) Please note that this mode transition is valid for 16MB devices only. DiskOnChip Millennium Plus has three modes of operation: Mode changes can occur due to any of the following events, as shown in Figure 13: * Power-Up Power Off Power-Down Power-Down Assert RSTIN#, Boot Detect or Software Control Reset Sequence End Reset Mode Power-Down Assert RSTIN# Release RSTIN# Deep Power-Down Mode 4x Read Cycles from offset 0x1FFF or extended read cycle Assert RSTIN# Software Control Normal Mode Figure 13: Operation Modes and Related Events ------ For DiskOnChip Millennium Plus 16MB only. 29 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 5.1 Normal Mode This is the mode in which standard operations involving the flash memory are performed. Normal mode is automatically entered when a valid write sequence is sent to the DiskOnChip Control register and Control Confirmation register. The boot detector circuit triggers the software to set the device to Normal mode. A write cycle occurs when both the CE# and WE# inputs are asserted. Similarly, a read cycle occurs when both the CE# and OE# inputs are asserted. Because the flash controller generates its internal clock from these CPU cycles and some read operations return volatile data, it is essential that the specified timing requirements contained in Section 10.4.1 be met. It is also essential that read and write cycles are not interrupted by glitches or ringing on the CE#, WE#, OE# address inputs. All inputs to DiskOnChip Millennium Plus are Schmidt Trigger types to improve noise immunity. In Normal mode, DiskOnChip Millennium Plus responds to every valid hardware cycle. When there is no activity, it is possible to reduce the power consumption to a typical deep-power-down current of 10 A (16/32MB) or 20 A (64MB) by setting the device in Deep Power-Down mode. 5.2 Reset Mode In Reset mode, DiskOnChip Millennium Plus ignores all write cycles, except for those to the DiskOnChip Control register and Control Confirmation register. All register read cycles return a value of 00H. Before attempting to perform a register read operation, the device is set to Normal mode by TrueFFS software. 5.3 Deep Power-Down Mode In Deep Power-Down mode, DiskOnChip Millennium Plus internal high current voltage regulators are disabled to reduce quiescent power consumption to 10 A-20 A typical. The following signals are also disabled in this mode: * * Standard interface: input buffers A[12:0], BHE#, WE#, D[15:0] and OE# (when CE# is negated) Multiplexed interface: input buffers AD[15:0], AVD#,WE# and OE# (when CE# is negated). To enter Deep Power-Down mode, a proper sequence must be written to the DiskOnChip Control registers and DiskOnChip Control Confirmation register, and the CE# input must be negated (32/64MB devices should have CE# input > VCC -0.2V, 16MB devices should have CE# = VCC). All other inputs should be VSS or VCC. DiskOnChip Millennium Plus 16MB device provides an additional option to set the device into Deep Power-Down mode. When in Normal mode, assertion of the RSTIN# signal and holding it in the low state puts the device in Deep Power-Down mode (see dotted line in Figure 13). When the RSTIN# signal is released, the device is set in Reset mode. In Deep Power-Down mode, write cycles have no effect and read cycles return indeterminate data (DiskOnChip Millennium Plus does not drive the data bus). Entering Deep Power-Down mode and then returning to the previous mode does not affect the value of any register. To exit Deep Power-Down mode, perform the following sequence: * Read four times from address 1FFFH. The data returned is undefined. (For DiskOnChip Millennium 16MB devices, this option is valid for both standard and multiplexed interface.) DiskOnChip Millennium Plus 16MB offers an additional method to exit Deep Power-Down mode when using a standard interface: * Perform a single read cycle from the Programmable Boot Block with an extended access time and address hold time as specified in Section 10.4.1. The data returned will be correct. Applications that require both Deep Power-Down mode and boot detection require BIOS support to ensure that DiskOnChip Millennium Plus exits from Power-Down mode prior to the expansion ROM scan. Similarly, applications that use DiskOnChip Millennium Plus as a boot ROM must ensure that the device is not in Deep Power-Down mode before reading the boot vector/instructions, either by pulsing RSTIN# to the asserted state and waiting for the BUSY# output to be negated, or by entering Reset mode via software. 30 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 6. 6.1 TrueFFS Technology General Description M-Systems' patented TrueFFS technology was designed to maximize the benefits of flash memory while overcoming inherent flash limitations that would otherwise reduce its performance, reliability and lifetime. TrueFFS emulates a hard disk, making it completely transparent to the OS. In addition, since it operates under the OS file system layer (see Figure 14), it is completely transparent to the application. Application OS File System TrueFFS DiskOnChip Figure 14: TrueFFS Location in System Hierarchy TrueFFS technology support includes: * * * * * * * * * * * * * Binary driver support for all major OSs TrueFFS Software Development Kit (TrueFFS SDK) Boot Software Development Kit (BDK) Support for all major CPUs, including 8, 16 and 32-bit bus architectures Block device API Flash file system management Bad block management Dynamic virtual mapping Dynamic and static wear-leveling Power failure management Implementation of Reed-Solomon EDC/ECC Performance optimization Compatible with all DiskOnChip products TrueFFS technology features: 6.1.1 Built-in Operating System Support The TrueFFS driver is integrated into all major OSs including: Windows CE, NT, NT Embedded, Symbian, Linux (various kernels), VxWorks, Nucleus, pSOS, QNX, DOS, and others. For a complete listing of all available drivers, please refer to M-Systems' website http://www.m-sys.com. It is advised to use the latest driver versions that can be downloaded from the DiskOnChip Millennium Plus web page on the M-Systems site. 31 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 6.1.2 TrueFFS Software Development Kit (SDK) The basic TrueFFS Software Development Kit (SDK) provides the source code of the TrueFFS driver. It can be used in an OS-less environment or when special customization of the driver is required for proprietary OSs. When using DiskOnChip Millennium Plus as the boot replacement device, TrueFFS SDK also incorporates in its source code the BDK, software that is required for this configuration (this package is also available separately). Please refer to the Boot Software Development Kit (BDK) developer guide for further information on using this software package. 6.1.3 File Management TrueFFS accesses the flash memory within DiskOnChip Millennium Plus through an 8KB window in the CPU memory space. It provides block device API, by using standard file system calls, identical to those used by a mechanical hard disk, to enable reading from and writing to any sector on DiskOnChip. This makes it compatible with any file system and file system utilities such as diagnostic tools and applications. When using the File Allocation Table (FAT) file system, the data stored on DiskOnChip uses FAT-16. Note: DiskOnChip Millennium Plus is shipped unformatted and contains virgin media. 6.1.4 Bad-Block Management NAND flash being an imperfect storage media, it contains some bad blocks that cannot be used for storage because of their high error rates. TrueFFS automatically detects and maps bad blocks upon system initialization, ensuring that they are not used for storage. This management process is completely transparent to the user, who remains unaware of the existence and location of bad blocks, while remaining confident of the integrity of data stored. The Bad Block Table in DiskOnChip Millennium Plus is hardware-protected for ensured reliability. 6.1.5 Wear-Leveling Flash memory can be erased a limited number of times. This number is called the erase cycle limit or write endurance limit and is defined by the flash array vendor. The erase cycle limit applies to each individual erase block in the flash device. In DiskOnChip Millennium Plus, the erase cycle limit of the flash is 1M erase cycles (commercial temperature) or 300,000 (extended temperature). This means that after approximately 300,000 erase cycles, the erase block begins to make storage errors at a rate significantly higher than the error rate that is typical to the flash. In a typical application and especially if a file system is used, a specific page or pages are constantly updated (e.g., the page/s that contain the FAT, registry etc.). Without any special handling, these pages would wear out more rapidly than other pages, reducing the lifetime of the entire flash. To overcome this inherent deficiency, TrueFFS uses M-Systems' patented wear-leveling algorithm. The wear-leveling algorithm ensures that consecutive writes of a specific sector are not written physically to the same page in the flash. This spreads flash media usage evenly across all pages, thereby maximizing flash lifetime. TrueFFS wear-leveling extends the flash lifetime 10 to 15 years beyond the lifetime of a typical application. Dynamic Wear-Leveling TrueFFS uses statistical allocation to perform dynamic wear-leveling on newly written data. This not only minimizes the number of erase cycles per block, it also minimizes the total number of erase cycles. Because a block erase is the most time-consuming operation, dynamic wear-leveling has a major impact on overall performance. This impact cannot be noticed during the first write to flash (since there is no need to erase blocks beforehand), but is more and more noticeable as the flash media becomes full. 32 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte Static Wear-Leveling Areas on the flash media may contain static files, characterized by blocks of data that remain unchanged for very long periods of time, or even for the whole device lifetime. If wear-leveling were only applied on newly written pages, static areas would never be cycled. This limited application of wear-leveling would lower life expectancy significantly in cases where flash memory contains large static areas. To overcome this problem, TrueFFS forces data transfer in static areas as well as in dynamic areas, thereby applying wear-leveling to the entire media. 6.1.6 Power Failure Management TrueFFS uses algorithms based on "erase after write" instead of "erase before write" to ensure data integrity during normal operation and in the event of a power failure. Used areas are reclaimed for erasing and writing the flash management information into them only after an operation is complete. This procedure serves as a check on data integrity. The "erase after write" algorithm is also used to update and store mapping information on the flash memory. This keeps the mapping information coherent even during power failures. The only mapping information held in RAM is a table pointing to the location of the actual mapping information. This table is reconstructed during power-up or after reset from the information stored in the flash memory. To prevent data from being lost or corrupted, TrueFFS uses the following mechanisms: * * When writing, copying, or erasing the flash device, the data format remains valid at all intermediate stages. Previous data is never erased until the operation has been completed and the new data has been verified. A data sector cannot exist in a partially written state. Either the operation is successfully completed, in which case the new sector contents are valid, or the operation has not yet been completed or has failed, in which case the old sector contents remain valid. 6.1.7 Error Detection/Correction TrueFFS implements a Reed-Solomon Error Correction Code (ECC) algorithm to ensure data reliability. Refer to Section 3.5 for further information on the EDC/ECC mechanism. 6.1.8 Special Features through I/O Control (IOCTL) Mechanism In addition to standard storage device functionality, the TrueFFS driver provides extended functionality. This functionality goes beyond simple data storage capabilities to include features such as: format the media, read/write protect, binary partition(s) access, flash defragmentation and other options. This unique functionality is available in all TrueFFS-based drivers through the standard I/O control command of the native file system. For further information, please refer to the Extended Functions of the TrueFFS Driver for DiskOnChip developer guide. 6.1.9 Compatibility The TrueFFS driver supports all released DiskOnChip products. Upgrading from one product to another requires no additional software integration. When using different drivers (e.g. TrueFFS SDK, Boot SDK, BIOS extension firmware, etc.) to access DiskOnChip Millennium Plus, the user must verify that all software is based on the same code base version. It is also important to use only tools (e.g. DFORMAT, DINFO, GETIMAGE, etc.) derived from the same version as the firmware version and the TrueFFS drivers used in the application. Failure to do so may lead to unexpected results, such as lost or corrupted data. The driver and firmware version can be verified by the sign-on messages displayed, or by the version information stored in the driver or tool. Note: When a new M-Systems DiskOnChip product with new features is released, a new TrueFFS version is required. 33 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 6.2 8KB Memory Window in DiskOnChip Millennium Plus 16/32MB TrueFFS utilizes an 8KB memory window in the CPU address space, consisting of four 2KB sections as depicted in Figure 15. When in Reset mode, read cycles from sections 1 and 2 always return the value 00H to create a fixed and known checksum. When in Normal mode, these two sections are used for the internal registers. The 1KB Programmable Boot Block is aliased twice, in section 0 and section 3, to support systems that search for a checksum at the boot stage both from the top and bottom of memory. The addresses described here are relative to the absolute starting address of the 8KB memory window. Reset Mode 000H Programmable boot block [000H-3FFH] (2 aliases) Normal Mode Programmable boot block [000H-3FFH] (2 aliases) Section 0 800H 00H Section 1 Flash area window (+ aliases) 1000H 00H Section 2 Control Registers (+ aliases) 1800H Programmable boot block [000H-3FFH] (2 aliases) Section 3 Programmable boot block [000H-3FFH] (2 aliases) Figure 15: DiskOnChip Millennium Plus 16/32MB Memory Map 34 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 6.3 8KB Memory Window in DiskOnChip Millennium Plus 64MB TrueFFS utilizes an 8KB memory window in the CPU address space consisting of four 2KB sections, as depicted in Figure 16. When in Reset mode, the Programmable Boot Block in sections 0 and 3 will show the IPL (1KB) of the first 32MB of the dual-die, aliased twice. Read cycles from sections 1 and 2 always return the value 00H to create a fixed and known checksum. After setting the MAX_ID field in the Configuration register (done by IPL0), the second copy of IPL 0 is replaced with the IPL of the second 32MB device of the dual-die, thereby creating a 2KB programmable boot block. When in Normal mode, sections 1 and 2 are used for the internal registers. The Programmable Boot Block in section 0 contains IPL0 and IPL1. Section 3 contains IPL0 aliased twice. Note: The addresses described here are relative to the absolute starting address of the 8KB memory window. Reset Mode 000H Programmable boot block [IPL] (2 aliases) Normal Mode Programmable boot block [IPL0, IPL1] Section 0 800H 00H Section 1 Flash area window (+ aliases) 1000H 00H Section 2 Control Registers (+ aliases) 1800H Programmable boot block [000H-3FFH] (2 aliases) Section 3 Programmable boot block [IPL0, IPL1] (2 aliases) Figure 16: DiskOnChip Millennium Plus 64MB Memory Map 35 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 7. Register Descriptions This section describes various DiskOnChip Millennium Plus registers and their functions, as listed in Table 5. This section can be used to enable the designer to better evaluate DiskOnChip technology. Table 5: DiskOnChip Millennium Plus Registers Address (Hex) 1000 1002 1004 1006 1008 100A 100C 100E 1046 1076 Register Name Chip Identification (ID) No Operation (NOP) Test DiskOnChip Control Device ID Select Configuration Output Control Interrupt Control Toggle Bit DiskOnChip Control Confirmation 7.1 RFU Definition of Terms Reserved for future use. This bit is undefined during a read cycle and "don't care" during a write cycle. Reserved for future use; when read, this bit always returns the value 0; when written, software should ensure that this bit is always set to 0. Reserved for future use; when read, this bit always returns the value 1; when written, software should ensure that this bit is always set to 1. Refers to the value immediately present after exiting from Reset mode to Normal mode. The following abbreviations and terms are used within this section: RFU_0 RFU_1 Reset Value 7.2 Reset Values All registers return 00H while in Reset mode. The Reset value written in the register description is the register value after exiting Reset mode and entering Normal mode. Some register contents are undefined at that time (N/A). 7.3 Chip Identification (ID) Register This register is used to identify the device residing on the host platform. For DiskOnChip Millennium Plus 32/64MB, this register always returns 40H when read. For DiskOnChip Millennium Plus 16MB, it returns 41H. 1000 Read only 40H/41H Bit 6 Bit 5 Bit 4 Bit 3 40H/41H Bit 2 Bit 1 Bit 0 Description: Address (hex): Type: Reset Value: Bit 7 36 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 7.4 No Operation (NOP) Register A call to this register results in no operation. To aid in code readability and documentation, software should access this register when performing cycles intended to create a time delay. 1002 Write None This register enables software to identify multiple DiskOnChip Millennium Plus devices or multiple aliases in the CPUs memory space. Data written is stored but does not affect the behavior of DiskOnChip Millennium Plus. 1004 Read/Write 00H Bit 6 Bit 5 Bit 4 D[7:0] Bit 3 Bit 2 Bit 1 Bit 0 Description: Address (hex): Type: Reset Value: 7.5 Test Register Description: Address (hex): Type: Reset Value: Bit 7 Bit No. 0-7 D[7:0]: Data bits Description 37 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 7.6 DiskOnChip Control Register/Control Confirmation Register These two registers are identical and contain information on the operation mode of DiskOnChip. After writing the required value to the DiskOnChip Control register, the complement of that data byte must also be written to the Control Confirmation register. The two writes cycles must not be separated by any other read or write cycles to DiskOnChip Millennium Plus memory space, except for reads from the Programmable Boot Block space. 1006/1076 Read/Write 10H Bit 6 RFU_0 Bit 5 Bit 4 RST_LAT Bit 3 BDET Bit 2 MDWREN Bit 1 Bit 0 Description: Address (hex): Type: Reset Value: Bit 7 Mode[1:0] Bit No. 0-1 Description Mode. These bits select the mode of operation, as follows: 00: Reset 01: Normal 10: Deep Power-Down MDWREN (Mode Write Enable). This bit must be set to 1 before changing the mode of operation. BDET (Boot Detect). This bit is set whenever the device has entered Reset mode as a result of the Boot Detector triggering. It is cleared by writing a 1 to this bit. RST_LAT (Reset Latch). This bit is set whenever the device has entered the Reset mode as a result of the RSTIN# input signal being asserted or the internal voltage detector triggering. It is cleared by writing a 1 to this bit. Reserved for future use. 2 3 4 5-7 38 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 7.7 Device ID Select Register In a cascaded configuration, this register controls which device provides the register space. The value of bits ID[0:1] is compared to the value of the ID configuration input pin/balls, as defined in Section 9.6. The device whose ID input pin/balls match the value of bits ID[0:1] responds to read and write cycles to register space. 1008 Read/Write 00H Bit 6 Bit 5 RFU_0 Bit 4 Bit 3 Bit 2 Bit 1 ID[1:0] Bit 0 Description: Address (hex): Type: Reset Value: Bit 7 Bit No. 0-1 2-7 Description ID[1:0] (Identification). The device whose ID input pins/balls match the value of bits ID[0:1] respond to read and write cycles to register space. Reserved for future use. 7.8 Configuration Register This register indicates the current configuration of the device. Unless otherwise noted, the bits are reset only by a hardware reset, and not upon boot detection or any other entry to Reset mode. 100A Read/Write (except bit 7, which is Read Only) X0000X10 Bit 6 RFU_0 Bit 5 MAX_ID Bit 4 Bit 3 RFU Bit 2 Bit 1 RFU_0 Bit 0 Description: Address (hex): Type: Reset Value: Bit 7 IF_CFG Bit No. 0-3, 6 4-5 Reserved for future use. Description MAX_ID (Maximum Device ID). This field controls the RAM address mapping when multiple devices are used in a cascaded configuration, using the ID[1:0] inputs. It should be programmed to the highest ID value that is found by software in order to map all available boot blocks into usable address space. IF_CFG (Interface Configuration). Reflects the state of the IF_CFG input pin. 7 39 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 7.9 Output Control Register This register controls the behavior of certain output pins. 100C Read/Write 01H Bit 6 RFU_0 Bit 5 Bit 4 Bit 3 SLOCK Bit 2 RFU_1 Bit 1 RFU_0 Bit 0 RFU_1 Description: Address (hex): Type: Reset Value: Bit 7 Bit No. 0-2, 4-7 3 Reserved for future use Description SLOCK [Sticky Lock]. Setting this bit to a 1 has the same effect as asserting the LOCK# input, up until the next power-up or reset. Once set, this bit can only be cleared by asserting the RSTIN# input. Like the LOCK# input, the assertion of this bit prevents the protection key from disabling the protection for a given partition if the value of the LOCK bit in its respective Data Protect Structure is set. When read, this bit always returns the value 0. Setting this bit affects the state of the LOCK# bit in the Protection Status register. Note: For further information on the Output Control and Protection Status registers, refer to the addendum to this data sheet, DiskOnChip Millennium Plus/DIMM Plus Register Description. 7.10 Interrupt Control Description: Address (hex): Type: Reset Value: Bit 7 RFU_0 Interrupts may be generated when the flash transitions from the busy state to the ready state, or by a data protection violation. 100E Read/Write 00H Bit 6 IRQ_P Bit 5 IRQ_F Bit 4 EDGE Bit 3 PROT_T Bit 2 Bit 1 FRDY_T[2:0 Bit 0 Bit No. 0-2 Description FRDY_T[2:0] (Flash Ready Trigger). This field determines if an interrupt will be generated when the flash array of DiskOnChip is ready, as follows: 000: Interrupts are disabled - Holds the IRQ# output in the negated state. 001: Interrupt when flash array is ready. PROT_T (Protection Trigger). When set, an interrupt is generated upon a data protection violation. EDGE (Edge-sensitive interrupt) 0: Specifies level-sensitive interrupts in which the IRQ# output remains asserted until the interrupt is cleared. 1: Specifies edge-sensitive interrupts in which the IRQ# output pulses low. IRQ_F: (Interrupt Request when flash array is ready) Indicates that the IRQ# output has been asserted due to an indication that the flash array is ready. Writing 1 to this bit clears its value, negates the IRQ# output and permits subsequent interrupts to occur. 3 4 5 40 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 6 IRQ_P (Interrupt Request on Protection Violation). Indicates that the IRQ# output has been asserted due to a data protection violation. Writing a 1 to this bit clears its value, negates the IRQ# output and permits subsequent interrupts to occur. Reserved for future use. 7 7.11 Toggle Bit Register Description: Address (hex): Type: Reset Value: Bit 7 This register identifies the presence of the device. 1046 Read Only 82H Bit 6 RFU Bit 5 Bit 4 RFU_0 Bit 3 RFU Bit 2 TOGGLE Bit 1 RFU_1 Bit 0 RFU Bit No. 0, 1, 3-7 2 Reserved for future use Description TOGGLE. This read-only bit toggles on consecutive reads and identifies the presence of the device. 41 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 8. 8.1 Booting from DiskOnChip Millennium Plus Introduction DiskOnChip Millennium Plus can function both as a flash disk and the system boot device. If DiskOnChip is configured as a flash disk, it can operate as the OS boot device. DiskOnChip default firmware contains drivers to enable it to perform as the OS boot device under DOS (see Section 8.2). For other OSs, please refer to the readme file of the TrueFFS driver. If DiskOnChip Millennium Plus is configured as a flash disk and as the system boot device, it contains the boot loader, an OS image and a file system. In such a configuration, DiskOnChip Millennium Plus can serve as the only non-volatile device on board. Refer to Section 8.3.2 for further information on boot replacement. 8.2 Boot Procedure in PC Compatible Platforms When used in PC compatible platforms, DiskOnChip Millennium Plus is connected to an 8KB memory window in the BIOS expansion memory range, typically located between 0C8000H to 0EFFFFH. During the boot process, the BIOS loads the TrueFFS firmware into the PC memory and installs DiskOnChip as a disk drive in the system. When the operating system is loaded, DiskOnChip is recognized as a standard disk. No external software is required to boot from DiskOnChip. Figure 17 illustrates the location of the DiskOnChip Millennium Plus memory window in the PC memory map. Extended Memory 0FFFFFH 0F0000H DiskOnChip 0C8000H 0B0000H RAM 8k BIOS 1M Display 640k 0 Figure 17: DiskOnChip Millennium Plus Memory Window in PC Memory Map After reset, the BIOS code first executes the Power On Self-Test (POST) and then searches for all expansion ROM devices. When DiskOnChip Millennium Plus is found, the BIOS code executes from it the IPL (Initial Program Loader) code, located in the XIP portion of the Programmable Boot Block. This code loads the TrueFFS driver into system memory, installs DiskOnChip Millennium Plus as a disk in the system, and then returns control to the BIOS code. The operating system subsequently identifies DiskOnChip Millennium Plus as an available disk. TrueFFS responds by emulating a hard disk. From this point onward, DiskOnChip Millennium Plus appears as a standard disk drive. It is assigned a drive letter and can be used by any application, without any modifications to either the BIOS set-up or the autoexec.bat/ config.sys files. DiskOnChip Millennium Plus can be used as the only disk in the system, with or without a floppy drive, and with or without hard disks. 42 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte The drive letter assigned depends on how DiskOnChip Millennium Plus is used in the system, as follows: * * If DiskOnChip Millennium Plus is used as the only disk in the system, the system boots directly from it and assigns it drive C. If DiskOnChip Millennium Plus is used with other disks in the system: o o * DiskOnChip Millennium Plus can be configured as the last drive (the default configuration). The system assigns drive C to the hard disk and drive D to DiskOnChip Millennium Plus. Alternatively, DiskOnChip Millennium Plus can be configured as the system's first drive. The system assigns drive D to the hard disk and drive C to DiskOnChip Millennium Plus. If DiskOnChip Millennium Plus is used as the OS boot device when configured as drive C, it must be formatted as a bootable device by copying the OS files onto it. This is done by using the SYS command when running DOS. 8.3 Boot Replacement 8.3.1 PC Architectures In current PC architectures, the first CPU fetch (after reset is negated) is mapped to the boot device area, also known as the reset vector. The reset vector in PC architectures is located at address FFFF0, by using a Jump command to the beginning of the BIOS chip (usually F0000 or E0000). The CPU executes the BIOS code, initializes the hardware and loads DiskOnChip Millennium Plus software using the BIOS expansion search routine (e.g. D0000). Refer to Section 8.2 for a detailed explanation on the boot sequence in PC compatible platforms. DiskOnChip Millennium Plus implements both disk and boot functions when it replaces the BIOS chip. To enable this, DiskOnChip Millennium Plus requires a location at two different addresses: * * After power-up, DiskOnChip Millennium Plus must be mapped in F segment, so that the CPU fetches the reset vector from address FFFF0, where DiskOnChip Millennium Plus is located. After the BIOS code is loaded into RAM and starts execution, DiskOnChip Millennium Plus must be reconfigured to be located in the BIOS expansion search area (e.g. D0000) so it can load the TrueFFS software. This means that the CS# signal must be remapped between two different addresses. For further information on how to achieve this, refer to application note AP-DOC-047, Designing DiskOnChip as a Flash Disk and Boot Device Replacement. 8.3.2 Non-PC Architectures In non-PC architectures, the boot code is executed from a boot ROM, and the drivers are usually loaded from the storage device. When using DiskOnChip Millennium Plus as the system boot device, the CPU fetches the first instructions from the DiskOnChip Millennium Plus Programmable Boot Block, which contains the IPL. Since in most cases this block cannot hold the entire boot loader, the Initial Program Loader (IPL) runs minimum initialization, after which the Secondary Program Loader (SPL) is copied to RAM from flash. The remainder of the boot loader code then runs from RAM. The IPL and SPL are located in a separate (binary) partition on DiskOnChip Millennium Plus, and can be hardware protected if required. For further information on software boot code implementation, refer to application notes AP-DOC-070, Writing an IPL for DiskOnChip Millennium Plus 32MB, and AP-DOC-044, Writing an IPL for DiskOnChip Millennium Plus 16MB. 43 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 8.3.3 Using DiskOnChip Millennium Plus in Asynchronous Boot Mode Platforms that host CPUs that wake up in burst mode should use Asynchronous Boot mode when using DiskOnChip Millennium Plus as the system boot device. During platform initialization, certain CPUs wake up in 32-bit mode and issue instruction fetch cycles continuously. XScale CPUs, for example, initiate a 16-bit read cycle, but after the first word is read, continue to hold CE# and OE# asserted while it increments the address and reads additional data as a burst. StrongARM CPUs wake up in 32-bit mode and issue double-word instruction fetch cycles. Since DiskOnChip Millennium Plus derives its internal clock signal from the CE#, OE# and WE# inputs, it cannot distinguish between these burst cycles. To support this type of access, DiskOnChip Millennium Plus needs to be set to Asynchronous Boot mode. To set DiskOnChip Millennium Plus to Asynchronous Boot mode, set the byte RAM MODE SELECT to 8FH. This can be done through the format utility of DiskOnChip Millennium Plus or by customizing the IPL code. For more information on the format utility, refer to the DiskOnChip Software Utilities user manual or the TrueFFS Software Development Kit (SDK) developer guide. For further details on customizing IPL code, refer to application note APDOC-044, Writing an IPL for DiskOnChip Millennium Plus 16MB. Once in Asynchronous Boot mode, the CPU can fetch its instruction cycles from the DiskOnChip Millennium Plus Programmable Boot Block. After reading from this block and completing boot, DiskOnChip Millennium Plus returns to derive its internal clock signal from the CE#, OE# and WE# inputs. Please refer to Section 10.4 for read timing specifications for Asynchronous Boot mode. Note: Only 16MB devices support Asynchronous Boot mode. 44 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 9. 9.1 * Design Considerations Design Environment Evaluation Boards (EVB) for enabling software integration and development with DiskOnChip Millennium Plus, even before the target platform is available. An EVB with DiskOnChip Millennium Plus soldered on it is available with an ISA standard connector and a PCI standard connector for immediate plug and play usage. Programming solutions o GANG programmer o Programming house o On-board programming TrueFFS Software Development Kit (SDK) and BDK DOS utilities o DFORMAT o GETIMG/PUTIMG o DINFO Documentation o Data sheet o Application notes o Technical notes o Articles o White papers DiskOnChip Millennium Plus provides a complete design environment consisting of: * * * * Please visit the M-Systems website (www.m-sys.com) for the most updated documentation, utilities and drivers. 45 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 9.2 System Interface 9.2.1 Standard Interface DiskOnChip Millennium Plus uses an SRAM-like interface that can easily be connected to any microprocessor bus. With a standard interface, it requires 13 address lines, 8 data lines and basic memory control signals (CE#, OE#, WE#), as shown in Figure 18 below. Typically, DiskOnChip Millennium Plus can be mapped to any free 8KB memory space. In a PC compatible platform, it is usually mapped into the BIOS expansion area. If the allocated memory window is larger than 8KB, an automatic anti-aliasing mechanism prevents the firmware from being loaded more than once during the ROM expansion search. 3.3 V 0.1 uF 10 nF 0.1 uF 1.8V/3.3V 10 nF 1-20KOhm Address Data Output Enable Write Enable Chip Enable Reset Chip ID A[12:0] VCC D[15:0] OE# WE# CE# RSTIN# ID[1:0] VSS VCCQ BUSY# Busy IRQ DiskOnChip Millennium Plus LOCK# BHE# IF_CFG Figure 18: Standard System Interface Notes: 1. The 0.1 F and the 10 nF low-inductance high-frequency capacitors must be attached to each of the device's VCC and VSS pins/balls. These capacitors must be placed as close as possible to the package leads. DiskOnChip Millennium Plus is an edge-sensitive device. CE#, OE# and WE# should be properly terminated (according to board layout, serial parallel or both terminations) to avoid signal ringing. All capacities support the standard interface. 2. 3. 46 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 9.2.2 Multiplexed Interface With a multiplexed interface, DiskOnChip Millennium Plus 16MB requires the signals shown in Figure 19 below. 3.3 V 0.1 uF 10 nF 0.1 uF 1.8V/3.3V . 10 nF 1-20KOhm Address/Data AVD# Output Enable W rite Enable Chip Enable Reset Chip ID AD[15:0] VCC AVD# OE# W E# CE# RSTIN# ID0 VSS VCCQ BUSY# IRQ# . . Busy DiskOnChip Millennium Plus LOCK# Figure 19: Multiplexed System Interface 9.3 Connecting Signals 9.3.1 Standard Interface DiskOnChip Millennium Plus uses standard SRAM-like control signals, which should be connected as follows: * * * * * * * * * * * Address (A[12:0]) - Connect these signals to the host address bus. Data (D[15:0]) - Connect these signals to the host data bus. Write (WE#) and Output Enable (OE#) - Connect these signals to the host WR# and RD# signals, respectively. Chip Enable (CE#) - Connect this signal to the memory address decoder. Chip Identification (ID[0:1]) -Both signals must be connected to VSS if only one DiskOnChip Millennium Plus is being used. If more than one, refer to Section 9.6 for more information on cascaded configuration. Power-On Reset In (RSTIN#) - Connect this signal to the host Power-On Reset signal. Busy (BUSY#) - Connect this signal to an input port. It indicates when the device is ready for first access after hardware reset. Interrupt (IRQ#) - Connect this signal to the host interrupt to release the host of this task and improve performance. Byte High Enable (BHE#) - This signal definition is compatible with 16 bit platforms that use the BHE#/BLE# protocol. See Section 9.5.4. This signal is only relevant during the boot phase. Hardware Lock (LOCK#) - This signal prevents the use of the Write Protect key to disable the protection. 8/16 Bit Configuration (IF_CFG) - This signal is required for configuring the device for 8 or 16-bit access mode. When negated, the device is configured for 8-bit access mode. When asserted, 16-bit access mode is operative. 47 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte DiskOnChip Millennium Plus derives its internal clock signal from the CE#, OE# and WE# inputs. Since access to DiskOnChip Millennium Plus' registers is volatile, much like a FIFO or UART, ensure that these signals have clean rising and falling edges, and are free from ringing that can be interpreted as multiple edges. PC board traces for these three signals must either be kept short or properly terminated to guarantee proper operation. When designing a 16-bit platform for both 8-bit and 16-bit DiskOnChip TSOP-I devices, please refer to application note AP-DOC-054, Connecting DiskOnChip TSOP-I to a 16-Bit Platform. 9.3.2 Multiplexed Interface DiskOnChip Millennium Plus 16MB can also be configured to work with a multiplexed interface where data and address line are multiplexed. In this configuration, AVD# input is driven by the host's AVD# signal, and the D[15:0] pins, used for both address and data, are connected to the host AD[15:0] bus. DiskOnChip address lines A[12:0] and BHE# should be connected to VSS. IF_CFG should be connected to VCC. Note: When the device operates with a multiplexed interface, the value of ID1 is internally forced to logic 0 due to the host AVD# signal. Since the only possible ID0 values are 0 and 1, a cascaded configuration supports up to two devices instead of four as with a standard interface. This mode is automatically entered when a falling edge is detected on AVD# input. This edge must occur after RSTIN# is negated and before OE# and CE# are both asserted, i.e. the first read cycle made to DiskOnChip must observe the multiplex mode protocol. Please refer to Section 2.3 for pinout and signal descriptions and to Section 10.4.3 for timing specifications for a multiplexed interface. 9.4 Implementing the Interrupt Mechanism 9.4.1 Hardware Configuration To configure the hardware, connect the IRQ# pin to the host interrupt input. Note: A nominal 10 K pull-up resistor must be connected to this pin. 9.4.2 Software Configuration Configuring the software to support the IRQ# interrupt is performed in two stages. Stage 1 Configure the software so that upon system initialization, the following steps occur: 1. The correct value is written to the Interrupt Control register to configure DiskOnChip for: * * 2. 3. 4. Interrupt source: Flash ready and/or data protection Output sensitivity: Either edge or level triggered Note: Refer to Section 7.10 for further information on the value to be written to this register. The host interrupt is configured to the selected input sensitivity, either edge or level. The handshake mechanism between the interrupt handler and the OS is initialized. The interrupt service routine to the host interrupt is connected and enabled. Stage 2 Configure the software so that for every long flash I/O operation, the following steps occur: 1. 2. 48 The correct value is written to the Interrupt Control register to enable the IRQ# interrupt. Note: Refer to Section 7.10 for further information on the value to be written to this register. The flash I/O operation starts. Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 3. 4. Control is returned to the OS to continue other tasks. When the IRQ# interrupt is received, other interrupts are disabled and the OS is flagged. The OS either returns control immediately to the TrueFFS driver, or waits for the appropriate condition to return control to the TrueFFS driver. For further information on implementing the interrupt mechanism, please refer to application note AP-DOC-063, Improving the Performance of DiskOnChip Plus Devices Using the IRQ# Pin. 9.5 Platform-Specific Issues The following section describes hardware design issues. 9.5.1 Wait State Wait states can be implemented only when DiskOnChip Millennium Plus is designed in a bus that supports a Wait state insertion, and supplies a WAIT signal. 9.5.2 Big and Little Endian Systems PowerPC, ARM, and other RISC processors can use either Big or Little Endian systems. DiskOnChip uses the Little Endian system. Therefore, bytes D[7:0] are its Least Significant Byte (LSB) and bytes D[15:8] are its Most Significant Byte (MSB). Within the bytes, bit D0 and bit D8 are the least significant bits of their respective byte. When connecting the DiskOnChip to a device that supports the Big Endian system, make sure to that the bytes of the CPU and DiskOnChip match. Note: Processors, such as the PowerPC, also change the bit ordering within the bytes. Failing to follow these rules results in improper connection of DiskOnChip and prevents the TrueFFS driver from identifying DiskOnChip. For further information on how to connect DiskOnChip Millennium Plus to support CPUs that use the Big Endian system, refer to the application note for the relevant CPU. 9.5.3 Busy Signal The Busy signal (BUSY#) indicates that DiskOnChip Millennium Plus has not yet completed internal initialization. After reset, BUSY# is asserted while the IPL is downloaded into the internal boot block and the Data Protection Structures (DPS) are downloaded to the Protection State Machines. Once the download process is completed, BUSY# is negated. It can be used to delay the first access to DiskOnChip Millennium Plus until it is ready to accept valid cycles. Note: The TrueFFS driver does NOT use this signal to indicate that the flash is in busy state (e.g. program, read, or erase). 9.5.4 Working with 8/16/32-Bit Systems with a Standard Interface When using a standard interface, DiskOnChip Millennium Plus can be configured for either 8-bit, 16-bit or 32-bit bus operations. 8-Bit (Byte) Data Access Mode When configured for 8-bit operation, IF_CFG should be negated. Data should then be driven only on the low data bus signals D[7:0]. D[15:8] and BHE# are internally pulled up and may be left floating. 16-Bit (Word) Data Access Mode When configured for 16-bit operation, IF_CFG should be asserted. The following definition is compatible with 16-bit platforms using the BHE#/BLE# protocol: * 49 When the host BLE# signal asserts DiskOnChip Millennium Plus A0, data is valid on D[7:0]. Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte * * * * When the host BHE# signal asserts DiskOnChip Millennium Plus BHE#, data is valid on D[15:8]. When both A[0] and BHE# are at logic 0, data is valid on D[15:0]. No data is transferred when both BHE# and A0 are logic 1. 16-bit hosts that do not support byte transfers may hardwire the A0 and BHE# inputs to logic 0. Table 6: Active Data Bus Lanes in 16-bit Configuration Inputs BHE# 0 0 1 1 A0 0 1 0 1 Data Bus Activity D[7:0] D[15:8] Word Odd Byte Even Byte No Operation Transfer Type Table 6 shows the active data bus lanes in a 16-bit configuration. Note: Although DiskOnChip Millennium Plus 16MB uses 8-bit access to the internal flash, it can be connected to a 16-bit bus. The TrueFFS driver handles all the issues regarding routing data to and from DiskOnChip Millennium Plus. The Programmable Boot Block is accessed as a true 16- bit device. It responds with the appropriate data when the CPU issues either an 8-bit or 16-bit read cycle. 32-Bit (Word) Data Access Mode In a 32-bit bus system that cannot execute byte- or word-aligned accesses, the system address lines SA0 and SA1 are always zero. Consecutive long-words (32-bit) are differentiated by SA2 toggling. Therefore, in 32-bit systems that support only 32-bit data access cycles, DiskOnChip A1 is connected to the first system address bit that toggles, i.e. SA2. DiskOnChip A0 is connected to VSS to configure it for 16-bit operation (see Table 6). System Host SA13 SA12 SA11 SA10 SA9 SA8 SA7 SA6 SA5 SA4 SA3 SA2 SA1 SA0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 DiskOnChip Figure 20: 32-bit (Word) Data Access Mode Note: The prefix "S" indicates system host address lines TrueFFS Driver Modifications TrueFFS supports a wide range of OSs (see Section 6.1.1). The TrueFFS driver is set to work in 8-bit data access mode as the default. To support 16-bit/32-bit data access modes and their related memory window allocations, TrueFFS must be modified. In Windows CE and Windows NT Embedded, these changes can be implemented through the Registry Entries. In all other cases, some minor customization is required in the driver. Please refer to the readme of each specific driver for further information. 50 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 9.6 Device Cascading 9.6.1 Standard Interface When using a standard interface, up to four DiskOnChip Millennium Plus 16/32MB or up to two DiskOnChip Millennium Plus 64MB devices can be cascaded, for up to 128MB capacity. No external decoding circuitry or system redesign is required. ID[1:0] pin/ball values determine the identity of each device. Systems with only one device must configure it as device 0 by setting ID[1:0] to 00H. Additional devices should be configured as device 1, device 2 and device 3 by setting ID[1:0] to 01H, 10H and 11H, respectively. Note: As DiskOnChip Millennium 64MB is a dual die comprised of two internally stacked DiskOnChip Millennium plus 32MB devices, only two DiskOnChip Millennium 64MB devices may be cascaded. When devices are cascaded, all I/O pins/balls must be wired in common, including the BUSY# output. The ID input pins/balls should be strapped to VCC or VSS, according to the location of each device. To communicate with a particular device, its ID must be written into the Device ID Select register (see Section 7.7). Only the device whose ID corresponds with this value responds to read or write cycles to registers. Figure 21 illustrates the configuration required to cascade four devices on the host bus. Only the relevant cascading signals are included in this figure, although all other signals must also be connected. VSS VSS VCC VSS ID0 ID1 VSS VCC VCC VCC 1st ID0 ID1 CE# OE# WE# 2nd ID0 ID1 CE# OE# WE# 3rd ID0 ID1 CE# OE# WE# 4th CE# OE# WE# CE# OE# WE# Figure 21: Cascading Configuration for Four Devices 9.6.2 Multiplexed Interface When using a multiplexed interface, up to two DiskOnChip Millennium Plus 16MB devices can be cascaded, for up to 32MB capacity. No external decoding circuitry or system redesign is required. ID0 pin/ball value determines the identity of each device. Systems with only one device must configure it as device 0 by connecting ID0 to VSS. The second device should be configured as device 1 by connecting ID0 to VCC. When two devices are cascaded, all I/O pins/balls must be wired in common, including the BUSY# output. To communicate with a particular device, its ID must be written into the Device ID Select register (see Section 7.7). Only the device whose ID corresponds with this value responds to read or write cycles to registers. 51 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 9.7 Memory Map in Cascaded Configuration When cascading DiskOnChip Millennium Plus devices, the Programmable Boot Block size is enlarged with 1KB for each additional device in the configuration. When four devices are connected in cascaded configuration, a boot block size of 4KB is available. The MAX_ID field of the Configuration register can be programmed with the maximum ID value used to enable access to the boot block of each device in a separate address space. Initially at power-up, only device 0 responds to reads from the boot block address space with its 1KB of data aliased at addresses 0K, 1K, 6K and 7K. Figure 22 shows the memory map when four devices are connected in a cascaded configuration, and the location of each IPL. Normal Mode (after setting MAX_ID) Section 0 Programmable Boot Block Reset Mode 0000H IPL 0 IPL 0 0800H 00H IPL 0 IPL 1 Section 1 Flash Area Window 1000H 00H Section 2 Control Registers IPL 2 1800H IPL 0 Section 3 Programmable Boot Block IPL 0 IPL 3 Figure 22: Memory Map in Cascaded Configuration 52 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 10. Product Specifications 10.1 Environmental Specifications 10.1.1 Operating Temperature Ranges Commercial Temperature Range: Extended Temperature Range: 0C to 70C -40C to +85C 10.1.2 Thermal Characteristics Table 7: Thermal Characteristics Thermal Resistance (C/W) Junction to Case (JC): 30 Junction to Ambient (JA): 85 10.1.3 Humidity 10% to 90% relative, non-condensing. 10.1.4 Endurance DiskOnChip Millennium Plus is based on NAND flash technology, which guarantees a minimum of 1M erase cycles (commercial temperature) or 300,000 erase cycles (extended temperature). Due to the TrueFFS wear-leveling algorithm, the life span of all DiskOnChip products is significantly prolonged. M-Systems' website (www.msys.com) provides an online life-span calculator to facilitate application-specific endurance calculations. 10.2 Disk Capacity Table 8: 64MB Disk Capacity (in bytes) DOS 6.22 Formatted Capacity 65,329,152 Sectors 127,596 VxWorks Formatted Capacity 65,568,768 Sectors 128,064 Table 9: 32MB Disk Capacity (in bytes) DOS 6.22 Formatted Capacity 32,800,768 Sectors 64,064 VxWorks Formatted Capacity 32,724,992 Sectors 63,916 Table 10: 16MB Disk Capacity (in bytes) DOS 6.22 Formatted Capacity 16,302,080 Sectors 31,840 VxWorks Formatted Capacity 16,367,616 Sectors 31,968 53 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 10.3 Electrical Specifications 10.3.1 Absolute Maximum Ratings Parameter DC Core Supply Voltage DC I/O Supply Voltage Input Pin Voltage Input pin Current Storage Temperature Lead Temperature Maximum duration of applying VCCQ without VCC or VCC without VCCQ Symbol VCC VCCQ VIN2 IIN TSTG TLEAD Tsupply 3 Rating1 -0.6 to 4.6 -0.6 to 4.6 -0.6 to VCCQ+0.3, 4.6V max -10 to 10 -55 to 150 260 500 Units V V V mA C C mS Notes 25 C 10 sec Applies to 16MB only (See Note 4) 1. Permanent device damage may occur if absolute maximum ratings are exceeded. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2. The voltage on any pin may undershoot to -2.0 V or overshoot to 6.6V for less than 20 ns. 3. For 32/64MB devices VCCQ=VCC. 4. When operating DiskOnChip with separate power supplies for Vcc and Vccq, it is desirable to turn both supplies on and off simultaneously. Providing power separately(either at power-on or power-off) can cause excessive power dissipation. Damage to the device may result if this condition persist for more than 1 second. 10.3.2 Capacitance Table 11: Capacitance for DiskOnChip Millennium Plus 16MB/32MB Parameter Input Capacitance Output Capacitance Capacitance is not 100% tested. Symbol CIN COUT Conditions VIN = 0V VOUT = 0V Min Typ Max 10 10 Unit pF pF Table 12: Capacitance for DiskOnChip Millennium Plus 64MB Parameter Input Capacitance Output Capacitance Capacitance is not 100% tested. Symbol CIN COUT Conditions VIN = 0V VOUT = 0V Min Typ Max 20 10 Unit pF pF 54 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 10.3.3 DC Electrical Characteristics Over Operating Range Table 13: DC Characteristics, 1.65V to 1.95V I/O (16MB Devices Only) Parameter Core Supply Voltage I/O Supply Voltage High-level Input Voltage Low-level Input Voltage High-level Output Voltage Symbol VCC VCCQ VIH VIL VOH IOh = -100 A D[15:0] Iol = 100 A IRQ#, BUSY# 4 mA VCCQ0.1V 0.1 V 0.3 10 10 Cycle Time = 100 ns Deep Power-Down mode5 All inputs 0V or VCCQ 25 10 1.7 45 40 6 A A mA A A Conditions Min 2.5 1.65 VCCQ0.4V 0.4 Typ 3.3 1.8 Max 3.6 1.95 Unit V V V V V Low-level Output Voltage VOL Input Leakage Current1,2 Output Leakage Current Active Supply Current 3 IILK IIOLK ICC ICCS ICCQS Standby Supply Current VCC Pins4 Standby Supply Current VCCQ Pins 1. The CE# input includes a pull-up resistor which sources 0.3~1.4 A at Vin=0V. 2. The D[15:8] and BHE# inputs each include a pull-up resistor which sources 58 ~ 234 A at Vin = 0V when IF_CFG is a logic-0. 3. VCC = 3.3V, VCCQ = 1.8V, Outputs open. 4. If DiskOnChip is not set to Deep Power-Down mode and is not accessed for read/write operation, standby supply current is 400 A (typ.) to 600 A (max.). 5. Deep Power-Down mode is achieved by asserting RSTIN# (when in Normal mode) or writing the proper write sequence to the DiskOnChip registers, and asserting the CE# input = VCCQ. See Section 5.3 for further details. 55 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte Table 14: DC Characteristics, 2.7V-3.6 I/O (16/32MB Devices) Parameter Core Supply Voltage I/O Supply Voltage High-level Input Voltage Low-level Input Voltage High-level Output Voltage Low-level Output Voltage High-level Output Current Low-level Output Current Input Leakage Current1, Output Leakage Current Active Supply Current 3 Symbol VCC VCCQ VIH VIL VOH VOL IOHM AX IOHMAX IILK IIOLK ICC ICCS Conditions Min 2.7 2.7 2.1 Typ 3.3 3.3 Max 3.6 3.6 0.7 Unit V V V V V V mA mA IOh = IOhmax IOl = IOlmax 3.0V < VCCQ < 3.6V 2.7V < VCCQ < 3.0V 3.0V < VCCQ < 3.6V 2.7V < VCCQ < 3.0V 2.4 0.4 -4 -4 8 5 10 10 A A mA A Cycle Time = 100 ns Deep Power-Down mode5 25 10 45 40 Standby Supply Current VCC Pins4 1. The CE# input includes a pull-up resistor which sources 0.3~1.4 uA at Vin=0V. 2. The D[15:8] and BHE# inputs each include a pull-up resistor which sources 58 ~ 234 A at Vin = 0V when IF_CFG is a logic-0. 3. VCC = VCCQ = 3.3V, Outputs open. 4. If DiskOnChip is not set to Deep Power-Down mode and is not accessed for read/write operation, standby supply current is 400 A (typ.) to 600 A (max.). 5. Deep Power-Down mode is achieved by asserting RSTIN# (when in Normal mode) or writing the proper write sequence to the DiskOnChip registers, and asserting the CE# input = VCCQ. See Section 5.3 for further details. 56 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte Table 15: DC Characteristics, 2.7V-3.6 I/O (64MB Devices) Parameter Core Supply Voltage I/O Supply Voltage High-level Input Voltage Low-level Input Voltage High-level Output Voltage Low-level Output Voltage High-level Output Current Low-level Output Current Input Leakage Current1, Output Leakage Current Active Supply Current 3 Symbol VCC VCCQ VIH VIL VOH VOL IOHM AX IOHMAX IILK IIOLK ICC ICCS Conditions Min 2.7 2.7 2.1 Typ 3.3 3.3 Max 3.6 3.6 0.7 Unit V V V V V V mA mA IOh = IOhmax IOl = IOlmax 3.0V < VCCQ < 3.6V 2.7V < VCCQ < 3.0V 3.0V < VCCQ < 3.6V 2.7V < VCCQ < 3.0V 2.4 0.4 -4 -4 8 5 10 10 A A mA A Cycle Time = 100 ns Deep Power-Down mode5 50 20 90 80 Standby Supply Current VCC Pins4 1. The CE# input includes a pull-up resistor which sources 0.3~1.4 uA at Vin=0V. 2. The D[15:8] and BHE# inputs each include a pull-up resistor which sources 58 ~ 234 A at Vin = 0V when IF_CFG is a logic-0. 3. VCC = VCCQ = 3.3V, Outputs open. 4. If DiskOnChip is not set to Deep Power-Down mode and is not accessed for read/write operation, standby supply current is 400 A (typ.) to 600 A (max.). 5. Deep Power-Down mode is achieved by asserting RSTIN# (when in Normal mode) or writing the proper write sequence to the DiskOnChip registers, and asserting the CE# input = VCCQ. See Section 5.3 for further details. 57 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 10.3.4 AC Operating Conditions Environmental and timing specifications are based on the following conditions. Table 16: AC Test Conditions Parameter Ambient Temperature (TA) Supply Voltage Input Pulse Levels Input Rise and Fall Times Input Timing Levels Output Timing Levels Output Load 1. For 16MB devices only VCCQ=1.65 to1.95V1 -40C to +85C 2.5V to 3.6V 0.2V to VCCQ-0.2V 3 ns 0.9V 0.9V 30 pF VCCQ=2.7-3.6V -40C to +85C 2.7V to 3.6V 0V to 2.7V 3 ns 1.5V 1.5V 100 pF 58 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 10.4 Timing Specifications 10.4.1 Read Cycle Timing Standard Interface TSU(A) A[12:0], BHE# THO(A) CE# THO(CE1) OE# TACC WE# TLOZ(D) D[15:0] THIZ(D) TREC(OE) TSU(CE0) THO(CE0) TSU(CE1) Figure 23: Standard Interface Read Cycle Timing TSU(A) A[12:0], BHE# AX THO(A) AY CE# THO(CE1) OE# TACC WE# TLOZ(D) D[15:0] DX THO(A-D) THIZ(D) DY TACC(A) TREC(OE) TSU(CE0) THO(CE0) TSU(CE1) Figure 24: Standard Interface Read Cycle Timing - Asynchronous Boot Mode 59 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte Table 17: Standard Interface Read Cycle Timing Parameters - DiskOnChip Millennium Plus 16MB 16MB (128Mb) Symbol Description VCCQ=VCC VCC=2.7-3.6V Min Tsu(A) Tho(A) Tsu(CE0) Tho(CE0) Tho(CE1) Tsu(CE1) Trec(OE) Tacc Tloz(D) Thiz(D) tacc(A) tho(A-D) Address to OE# OE# CE# OE# CE# to OE# to CE# to WE# setup time setup time hold time to CE# or OE# 2 1 VCCQ=1.65-1.9V VCC=2.7-3.6V Min -2 28 -- -- 6 6 20 Max Units Max -2 28 -- -- 6 6 20 101 3 ns ns ns ns ns ns ns 111 92 ns ns ns 27 98 ns ns ns to Address hold time OE# or WE# hold time setup time OE# negated to start of next cycle Read access time (RAM)3,4,5 Read access time (all other addresses) OE# OE# to D driven 6 82 15 23 15 to D Hi-Z delay Asynchronous Boot Mode RAM Read access time from A[9:1] Data hold time from A[9:1] (RAM) 0 89 0 1. CE# may be asserted any time before or after OE# is asserted. If CE# is asserted after OE#, all timing relative to when OE# was asserted will be referenced to the time CE# was asserted. 2. CE# may be negated any time before or after OE# is negated. If CE# is negated before OE#, all timing relative to when OE# was negated will be referenced to the time CE# was negated. 3. The boot block is located at addresses 0000~07FFH and 1800H~1FFFH. Registers located at addresses 0800H~17FFH have a faster access time than the boot block. Access to the boot block is not required after the boot process has completed. 4. Systems that do not access the boot block may implement only the read access timing for "all other registers". This will increase the systems performance, however it will prevent access to the boot block. 5. Add 260 ns on the first read cycle when exiting Power-Down mode. See Section 5.3 for more information. 6. No load (CL = 0 pF). 60 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte Table 18: Standard Interface Read Cycle Timing Parameters - DiskOnChip Millennium Plus 32/64MB 32/64MB (256/512Mb) Symbol Description VCC=VCCQ= 2.7 to 3.6V Min Tsu(A) Tho(A) Tsu(CE0) Tho(CE0) Tho(CE1) Tsu(CE1) Trec(OE) Tacc Tloz(D) Thiz(D) Address to OE# OE# CE# OE# CE# to OE# to CE# to WE# setup time setup time hold time to CE# or OE# 2 1 Units Max ns ns ns ns ns ns ns 103 ns ns ns 25 ns 85 10 28 -- -- 6 6 20 3 to Address hold time OE# or WE# hold time setup time OE# negated to start of next cycle Read access time (RAM)3,4 Read access time (all other addresses) OE# OE# to D driven 5 10 to D Hi-Z delay 1. CE# may be asserted any time before or after OE# is asserted. If CE# is asserted after OE#, all timing relative to when OE# was asserted will be referenced to the time CE# was asserted. 2. CE# may be negated any time before or after OE# is negated. If CE# is negated before OE#, all timing relative to when OE# was negated will be referenced to the time CE# was negated. 3. The boot block is located at addresses 0000~07FFH and 1800H~1FFFH. Registers located at addresses 0800H~17FFH have a faster access time than the boot block. Access to the boot block is not required after the boot process has completed. 4. Systems that do not access the boot block may implement only the read access timing for "all other registers". This will increase the systems performance, however it will prevent access to the boot block. 5. No load (CL = 0 pF). 61 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 10.4.2 Write Cycle Timing Standard Interface tTWCYC TSU(A) A[12:0], BHE# THO(CE1 CE# TSU(CE0) OE# THO(A) THO(CE0) Tw(WE) TSU(CE1 TREC(WE) WE# tSU(D) D[15:0] THO(D) Figure 25: Standard Interface Write Cycle Timing Table 19: Standard Interface Write Cycle Parameters - DiskOnChip Millennium Plus 16MB 16MB (128Mb) Symbol Description VCCQ=VCC VCC=2.7-3.6V Min Max VCCQ=1.65-1.9V VCC=2.7-3.6V Min Max Units TSU (A) Tho(A) Tw(WE) TWCYC Tsu (CE0) Tho (CE0) Tho (CE1) Tsu (CE1) Trec (WE) Tsu(D) Tho (D) Address to WE# WE# setup time -2 28 49 79 --6 6 20 27 0 -2 28 48 79 --6 6 20 28 0 ns ns ns ns ns ns ns ns ns ns to Address hold time WE# asserted width Write Cycle Time CE# WE# CE# WE# WE# to WE# to CE# to WE# setup time1 hold time2 to CE# or OE# hold time setup time OE# or WE# to start of next cycle setup time to D hold time D to WE# 1. CE# may be asserted any time before or after WE# is asserted. If CE# is asserted after WE#, all timing relative to WE# asserted should be referenced to the time CE# was asserted. 2. CE# may be negated any time before or after WE# is negated. If CE# is negated before WE#, all timing relative to WE# negated will be referenced to the time CE# was negated. 62 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte Table 20: Standard Interface Write Cycle Parameters - DiskOnChip Millennium Plus 32/64MB 32/64MB (256/512Mb) Symbol Description VCC=VCCQ= 2.7 to 3.6V Min Max Units tSU (A) tho (A) tw(WE) TWCYC tsu (CE0) tho (CE0) tho (CE1) tsu (CE1) trec (WE) tsu(D) tho (D) Address to WE# WE# setup time 10 28 47 80 -- -- 6 6 20 51 0 ns ns ns ns ns ns ns ns ns ns to Address hold time Write Cycle Time WE# asserted width CE# WE# CE# to WE# to CE# setup time1 hold time 2 OE# or WE# to CE# hold time setup to WE# or OE# time D to WE# WE# WE# to start of next cycle setup time to D hold time 1. CE# may be asserted any time before or after WE# is asserted. If CE# is asserted after WE#, all timing relative to WE# asserted should be referenced to the time CE# was asserted. 2. CE# may be negated any time before or after WE# is negated. If CE# is negated before WE#, all timing relative to WE# negated will be referenced to the time CE# was negated. 63 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 10.4.3 Read Cycle Timing Multiplexed Interface Tw(AVD) AVD# TSU(AVD) AD[15:0] ADDR TSU(CE0) CE# THO(CE1) OE# TREC(OE) WE# THO(CE0) TSU(CE1) TACC THO(AVD) DATA THIZ(D) Figure 26: Multiplexed Interface Read Cycle Timing Table 21: Multiplexed Interface Read Cycle Parameters 16MB (128Mb) Symbol Description VCCQ=VCC VCC=2.7-3.6V VCCQ=1.65-1.9V VCC=2.7-3.6V Units Min tsu(AVD) tho(AVD) Tw(AVD) tsu(CE0) 1 Max Min 5 7 12 -- -- 6 6 20 Max ns ns ns ns ns ns ns 111 92 ns Address to AVD# Address to AVD# CE# OE# CE# to OE# to CE# setup time hold time setup time 1 5 7 12 -- -- 6 6 20 101 82 15 23 AVD# low pulse width hold time2 hold time setup tho(CE0) 2 tho(CE1) tsu(CE1) trec(OE) Tacc tloz(D) 3 Thiz(D) OE# or WE# to CE# to WE# or OE# time OE# negated to start of next cycle Read access time (RAM) Read access time (all other addresses) OE# OE# to D driven to D Hi-Z delay 15 27 ns ns 1. CE# may be asserted any time before or after OE# is asserted. If CE# is asserted after OE#, all timing relative to OE# asserted will be referenced instead to the time of CE# asserted. 2. CE# may be negated any time before or after OE# is negated. If CE# is negated before OE#, all timing relative to OE# negated will be referenced instead to the time of CE# negated. 3. No load (CL = 0 pF). 64 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 10.4.4 Write Cycle Timing Multiplexed Interface Tw(AVD) AVD# TSU(AVD) AD[15:0] THO(CE1) CE# TSU(AVD-WE) TSU(CE0) OE# Tw(WE) WE# TWCYC TREC(WE) THO(CE0) TSU(CE1) ADDR THO(AVD) DATA TSU(D) THO(D) TREC(WE-AVD) NEXT ADDR Figure 27: Multiplexed Interface Write Cycle Timing Table 22: Multiplexed Interface Write Cycle Parameters 16MB (128Mb) Symbol Description VCCQ=VCC VCC=2.7-3.6V Min Max VCCQ=1.65-1.9V VCC=2.7-3.6V Min Max Units tsu(AVD) tho(AVD) Tw(AVD) tsu(AVD-WE) 1 Trec(WE-AVD) tw(WE) Twcyc tsu(CE0) tho(CE0) 1 2 Address to AVD# Address to AVD# AVD# WE# to WE# to AVD# setup time hold time setup time in next cycle 3 5 7 12 4 28 48 49 79 -- -- 6 6 20 27 0 5 7 12 4 30 47 48 79 -- -- 6 6 20 28 0 ns ns ns ns ns ns ns ns ns ns ns ns ns AVD# low pulse width WE# asserted width (RAM) Write Cycle Time CE# WE# CE# WE# WE# to WE# to CE# to WE# WE# asserted width (all other addresses) setup time hold time to CE# or OE# hold time setup time tho(CE1) tsu(CE1) trec(WE) Tsu(D) Tho(D) OE# or WE# to start of next cycle setup time (RAM) to D hold time D to WE# 1. CE# may be asserted any time before or after WE# is asserted. If CE# is asserted after WE#, all timing relative to WE# asserted will be referenced instead to the time of CE# asserted. 2. CE# may be negated any time before or after WE# is negated. If CE# is negated before WE#, all timing relative to WE# negated will be referenced instead to the time of CE# negated. 3. WE# may be asserted before or after the rising edge of AVD#. The beginning of the WE# asserted pulse width spec is measured from the later of the falling edge of WE# or the rising edge of AVD#. 65 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 10.4.5 Power-Up Timing DiskOnChip Millennium Plus is reset by assertion of the RSTIN# input. When this signal is negated, DiskOnChip initiates a download procedure from the flash memory into the internal Programmable Boot Block. During this procedure, DiskOnChip Millennium Plus does not respond to read or write accesses. Host systems must therefore observe the requirements described below for first access to DiskOnChip Millennium Plus. Any of the following methods may be employed to guarantee first-access timing requirements: a. b. c. Use a software loop to wait at least Tp (BUSY1) before accessing the device after the reset signal is negated. Poll the state of the BUSY# output. Use the BUSY# output to hold the host CPU in wait state before completing the first access. Host systems that boot from DiskOnChip Millennium Plus must employ option c), or use another method to guarantee the required timing for first-time access. VCC = 2.5V VCCQ = 1.65 or 2.5V VCC TREC(VCC-RSTIN) TW(RSTIN) RSTIN# TP(VCC-BUSY0) BUSY# THO(BUSY-A) A[12:0], BHE# TP(BUSY0) TP(BUSY1) VALID THO(BUSY-CS) CE#, OE#, WE# TSU(D-BUSY1) D (Read cycle) THO(RSTIN-AVD) AVD# (Muxed Mode Only) Figure 28: Reset Timing 66 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte Table 23: Power-Up Timing Parameters Symbol Description 1 Min Max Units TREC (VCC-RSTIN) Tp (VCC-BUSY0) TW (RSTIN) TP (BUSY0) TP (BUSY1)2 THO (BUSY-CE)3 TSU (D-BUSY1) 3 4 1 VCC/VCCQ stable to RSTIN# VCC/VCCQ stable to BUSY# RSTIN# asserted pulse width RSTIN# RSTIN# BUSY# RSTIN# to BUSY# to BUSY# to CE# 500 500 30 50 1.3 0 0 70 s s ns ns ms ns ns ns Data valid to BUSY# to AVD# low hold Tho(RSTIN-AVD) 1. Specified from the final positive crossing of Vcc above 2.7V. 2. If the assertion of RSTIN# occurs during a flash erase cycle, this time could be extended by up to 500 S. 3. Normal read/write cycle timing applies. This parameter applies only when the cycle is extended until the negation of the BUSY# signal. 4. Applies to multiplexed interface only. 10.4.6 Interrupt Timing The interrupt timing is illustrated in Figure 29, and described in Table 24. Tw(IRQ) IRQ# Figure 29: IRQ# Pulse Width in Edge Mode Table 24: Interrupt Timing Symbol Description Min Max Units Tw(IRQ) IRQ# asserted pulse width (edge mode) 300 800 nS 67 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 10.5 Mechanical Dimensions See Figure 30 and Figure 31 for the mechanical dimensions of the TSOP-I and BGA packages. TSOP-I Dimensions: 20.00.25 mm x 12.00.10 mm x 1.20.1 mm Figure 30:TSOP-I Package 68 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte BGA Dimensions (16/32MB): BGA Dimensions (64MB): Ball Pitch: 9.0 9.00.20 mm x 12.00.20 mm x 1.20.1 mm 9.00.20 mm x 12.00.20 mm x 1.40.1 mm 0.8mm 1.2 0.330.05 0.90 0.40 7.20 0.80 0.80 M L K J H 0.470.05 12.0 F E D C B A 0.80 1 2 3 4 5 6 7 8 9 10 0.80 0.40 G 2.40 7.20 Figure 31: BGA Package 69 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte 11. Ordering Information MDxxxx-Dxx-V3[Q18]-T-C MD: M-Systems DiskOnChip Version D: Capacity V: Voltage T: Temperature Range MD2811 - DiskOnChip Millennium Plus TSOP, MD3831, MD3331 - DiskOnChip Millennium Plus single/dual die BGA 64, 32, 16 V3 V3Q18 Blank X C: Composition Blank P Capacity: 32MB (256Mb) or 16MB (128Mb) Core and I/O Voltage: 3.3V Core Voltage: 3.3V, I/O Voltage: 1.8 or 3.3V Commercial: 0C to +70C Extended: -40C to +85C Regular Lead-free Table 25: Available Combinations Order Numbers Capacity MB Mb Package Temperature Range Composition Refer to Table 25 for the combinations currently available and the associated order numbers. MD2811-D16-V3Q18 MD2811-D16-V3Q18-P MD2811-D16-V3Q18-X MD2811-D16-V3Q18-X-P Commercial 48-pin TSOP-I Extended 16 128 69-ball BGA 9x12 mm Commercial Extended Commercial 48-pin TSOP-I Extended 32 256 69-ball BGA 9x12 mm Commercial Extended Commercial Extended Regular Lead-free Regular Lead-free Regular Lead-free Regular Lead-free Regular Lead-free Regular Lead-free Regular Lead-free Regular Lead-free Regular Lead-free Regular Lead-free MD3831-D16-V3Q18 MD3831-D16-V3Q18-P MD3831-D16-V3Q18-X MD3831-D16-V3Q18-X-P MD2811-D32-V3 MD2811-D32-V3-P MD2811-D32-V3-X MD2811-D32-V3-X-P MD3831-D32-V3 MD3831-D32-V3-P MD3831-D32-V3-X MD3831-D32-V3-X-P MD3331-D64-V3 MD3331-D64-V3-P MD3331-D64-V3-X MD3331-D64-V3-X-P 64 512 69-ball BGA 9x12 mm 70 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte Appendix A: Example Code This appendix provides example code to verify basic DiskOnChip Millennium Plus 32MB operations in the system, mainly useful at first integration stages. /*------------------------------------------------------------------------------*/ /* /* /* The target of this sequence is to make sure that DiskOnChip Millennium Plus /* is alive and responds to basic commands. /* /* Returns: TRUE if DiskOnChip Millennium Plus responds, otherwise FALSE. Identify DiskOnChip Millennium Plus 32MB */ */ */ */ */ */ /*------------------------------------------------------------------------------*/ /* Release from Power Down Mode (just in case) by performing 3 consecutive /* reads from anywhere + 1 from 0x1fff for(i = 0;( i < 4 ); i++ ) read from offset 0x1fff /* If DiskOnChip Millennium Plus was in Power-Down mode, it is now in Normal mode*/ /* If DiskOnChip Millennium Plus was in any other mode, it remains in that mode.*/ /* Set DiskOnChip Millennium Plus to Reset mode Write 0x1c to offset 0x1006 Write 0xe3 to offset 0x1076 /* to DiskOnChip Control Register */ /* to DiskOnChip Control Confirmation Register */ */ */ */ /* Set DiskOnChip Millennium Plus to Normal mode Write 0x1d to offset 0x1006 Write 0xe2 to offset 0x1076 /* to DiskOnChip Control Register */ */ /* to DiskOnChip Control Confirmation Register */ */ /* Verify that DiskOnChip is in Normal mode. Read from offset 0x1006 into temp if (temp&0x01) != 1 return (FALSE) /* Check Chip ID Read from offset 0x1000 into temp if temp!=0x40 return(FALSE) */ /* Check toggle bit /* The toggle bit should toggle on each consecutive read. Read from offset 0x1046 into temp1 Read from offset 0x1046 into temp2 Read from offset 0x1046 into temp3 If ((temp1&0x04) = (temp2&0x04)) return (FALSE) If ((temp2&0x04) = (temp3&0x04)) return (FALSE) If (temp1&0x04) != (temp1&0x04) return (FALSE) */ */ /* Check Test Register 71 Data Sheet, Rev. 1.7 */ 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte Write 0x16 to offset 0x1004 Read from offset 0x1004 into temp If temp != 0x16 return (FALSE) Write 0x03 to offset 0x1004 Read from offset 0x1004 into temp if temp != 0x03 return (FALSE) Return (True) /* If True, then DiskOnChip Millennium Plus is alive and responding*/ 72 Data Sheet, Rev. 1.7 93-SR-002-03-8L DiskOnChip Millennium Plus 16/32/64MByte How to Contact Us Internet: General Information: Sales and Technical Information: USA M-Systems Inc. 8371 Central Ave, Suite A Newark CA 94560 Phone: +1-510-494-2090 Fax: +1-510-494-5545 Taiwan M-Systems Asia Ltd. Room B, 13 F, No. 133 Sec. 3 Min Sheng East Road Taipei, Taiwan R.O.C. Tel: +886-2-8770-6226 Fax: +886-2-8770-6295 Japan Asahi Seimei Gotanda Bldg., 3F 5-25-16 Higashi-Gotanda Shinagawa-ku Tokyo, 141-0022 Tel: +81-3-5423-8101 Fax: +81-3-5423-8102 http://www.m-sys.com info@m-sys.com techsupport@m-sys.com China M-Systems China Ltd. 25A International Business Commercial Bldg. Nanhu Rd., Lou Hu District Shenzhen, China 518001 Phone: +86-755-2519-4732 Fax: +86-755-2519-4729 Europe M-Systems Ltd. 7 Atir Yeda St. Kfar Saba 44425, Israel Tel: +972-9-764-5000 Fax: +972-3-548-8666 (c) 2003 M-Systems Flash Disk Pioneers, Ltd. All rights reserved. This document is for information use only and is subject to change without prior notice. M-Systems Flash Disk Pioneers Ltd. assumes no responsibility for any errors that may appear in this document. No part of this document may be reproduced, transmitted, transcribed, stored in a retrievable manner or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without prior written consent of M-Systems. M-Systems products are not warranted to operate without failure. Accordingly, in any use of the Product in life support systems or other applications where failure could cause injury or loss of life, the Product should only be incorporated in systems designed with appropriate and sufficient redundancy or backup features. Contact your local M-Systems sales office or distributor, or visit our website at www.m-sys.com to obtain the latest specifications before placing your order. DiskOnChip(R), DiskOnChip Millennium(R), DiskOnKey(R) and TrueFFS(R) are registered trademarks of M-Systems. DiskOnKey MyKeyTM, FFDTM and SuperMAPTM are trademarks of M-Systems. Other product names mentioned in this document may be trademarks or registered trademarks of their respective owners and are hereby acknowledged. 73 Data Sheet, Rev. 1.7 93-SR-002-03-8L |
Price & Availability of MD2811
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |